Axxess AXLOC-FD2

Axxess AXLOC-FD2 2-Channel Line Output Converter Instruction Manual for Ford 2011-Up

Model: AXLOC-FD2

Zavedení

The Axxess AXLOC-FD2 is a 2-channel line output converter designed to integrate aftermarket amplifiers with factory audio systems in select Ford vehicles from 2011 and newer. This device converts high-level speaker signals from the factory radio into low-level RCA signals, providing a clean and adjustable output for your amplifier. It also provides a 12-volt accessory output for ampzapnutí zvlhčovače.

Bezpečnostní informace

  • Před zahájením jakékoli instalace vždy odpojte záporný pól baterie vozidla.
  • Ujistěte se, že všechna kabelová spojení jsou bezpečná a řádně izolovaná, aby se zabránilo zkratu.
  • Pokud si nejste jisti některou částí procesu instalace, poraďte se s profesionálním instalatérem autorádií.
  • Do not operate the vehicle's audio system at excessively high volumes for prolonged periods, as this may cause hearing damage.
  • Mount the converter in a location that is protected from moisture and excessive heat.

Obsah balení

Před zahájením instalace ověřte, zda jsou všechny položky přítomny:

  • AXLOC-FD2 Line Output Converter Module
  • Vehicle-specific wiring harness
  • RCA output cables
  • Remote turn-on wire
Various components of the Axxess AXLOC-FD2 kit, including the main converter module, wiring harnesses, and RCA cables.
Figure 1: Components included in the Axxess AXLOC-FD2 kit. This image displays the main converter unit, various wiring harnesses with connectors, and RCA cables, illustrating the complete set of parts for installation.

Pokyny k instalaci

This section outlines the general installation procedure. Specific vehicle disassembly instructions are beyond the scope of this manual. Refer to a vehicle-specific service manual for dash removal and access to the factory radio wiring.

Požadované nástroje:

  • Odizolovače/krimpovače drátů
  • Elektrická páska nebo smršťovací bužírka
  • Multimetr
  • Nástroje pro odstranění panelu
  • Screwdrivers/socket set

Schéma zapojení a připojení:

  1. Odpojit baterii: Před nastartováním odpojte záporný pól baterie vozidla, abyste předešli elektrickému zkratu.
  2. Access Factory Radio: Carefully remove the necessary trim panels and components to gain access to the back of the factory radio.
  3. Identifikace reproduktorových kabelů: Using a vehicle-specific wiring diagram or a multimeter, identify the factory speaker output wires (positive and negative for each channel) from the factory radio harness.
  4. Connect Input Harness: Connect the vehicle-specific wiring harness provided with the AXLOC-FD2 to the factory radio harness. This harness will typically plug in-line with the factory radio, intercepting the speaker outputs.
  5. Connect AXLOC-FD2 Module: Plug the main connector from the vehicle-specific harness into the AXLOC-FD2 module.
  6. Připojení RCA výstupů: Connect the RCA output cables from the AXLOC-FD2 module to the RCA inputs of your aftermarket ampživější.
  7. Connect Remote Turn-On: The AXLOC-FD2 provides a 12-volt accessory output (remote turn-on) for your amplifier. Connect this wire to the remote turn-on input of your amplifier. This eliminates the need to find a separate switched 12V source.
  8. Zemní připojení: Ensure the AXLOC-FD2 module has a solid ground connection. The vehicle-specific harness should provide this, but always verify.
  9. Montáž: Securely mount the AXLOC-FD2 module in a suitable location, away from heat and moisture, ensuring it does not interfere with any moving parts or vehicle components.
Axxess AXLOC-FD2 wiring harness and converter units laid out, showing the main connections.
Obrázek 2: Přesview of the AXLOC-FD2 wiring harness and converter units. This image illustrates how the main harness connects to the converter module, providing a visual guide for the primary connections during installation.
Detailní view of the Axxess AXLOC-FD2 converter module and various connectors.
Obrázek 3: Detailní view of the AXLOC-FD2 converter module and associated connectors. This image provides a closer look at the input and output ports on the converter, as well as the design of the various plugs and sockets.

Návod k obsluze

Úprava zisku:

The AXLOC-FD2 features adjustable gain controls to match the output level of the factory radio to the input sensitivity of your aftermarket amplifier. Proper gain setting is crucial for optimal sound quality and to prevent distortion.

  1. Počáteční nastavení: Start with the gain controls on the AXLOC-FD2 set to their minimum position (fully counter-clockwise).
  2. AmpZisk lifikátoru: Set the gain control on your aftermarket amplifier to its minimum position.
  3. Přehrát hudbu: Play a dynamic piece of music through your factory radio at about 75% of its maximum volume.
  4. Adjust AXLOC-FD2 Gain: Slowly increase the gain controls on the AXLOC-FD2 until you hear a slight distortion, then back off slightly until the sound is clean.
  5. Upravit AmpZisk lifikátoru: Once the AXLOC-FD2 gain is set, slowly increase the gain control on your amplifier until the desired volume is achieved without distortion.
  6. Doladění: Make small adjustments to both the AXLOC-FD2 and amplifier gains as needed to achieve the best sound quality. Avoid setting gains too high, as this will introduce distortion and can damage speakers.

Údržba

The Axxess AXLOC-FD2 is designed for reliable, maintenance-free operation. No user-serviceable parts are inside. To ensure longevity:

  • Udržujte jednotku bez prachu a nečistot.
  • Ujistěte se, že všechna kabelová připojení zůstanou bezpečná.
  • Nevystavujte jednotku extrémním teplotám nebo vlhkosti.

Odstraňování problémů

ProblémMožná příčinaŘešení
No audio output from ampdoživotní
  • Loose RCA connections
  • No remote turn-on signal to ampdoživotní
  • Incorrect input wiring to AXLOC-FD2
  • Ampzáchranář není napájen
  • Check and secure all RCA cables.
  • Verify remote turn-on wire is connected and receiving 12V.
  • Double-check speaker input wiring from factory radio.
  • Zajistit amplifier has power and ground connections.
Zkreslený nebo špatná kvalita zvuku
  • Gain levels set too high
  • Špatné zemní spojení
  • Nesprávná polarita reproduktorů
  • Re-adjust gain settings on AXLOC-FD2 and amplifier (refer to Operating Instructions).
  • Verify a solid, clean ground connection for both AXLOC-FD2 and ampživější.
  • Check speaker wire polarity; ensure positive and negative are consistent.
Hissing or whining noise
  • Rušení zemní smyčky
  • Špatná kvalita RCA kabelů
  • Ensure all components are grounded to the same point.
  • Try routing RCA cables away from power wires.
  • Consider using higher quality shielded RCA cables.

Specifikace

  • Model: AXLOC-FD2
  • kanály: 2-kanál
  • Typ vstupu: High-level (speaker level)
  • Typ výstupu: Low-level (RCA)
  • Kompatibilita: Ford vehicles 2011-Up
  • Vlastnosti: Adjustable gain, 12V remote turn-on output
  • Hmotnost položky: Přibližně 1.37 libry
  • Rozměry balení: Přibližně 10.39 x 10.31 x 4.92 palce

Záruka a podpora

Informace o záruce nebo technickou podporu získáte od oficiálního webnebo se obraťte na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.

Výrobce: Axxess

Webmísto: axxessinterfaces.com (Napřampodkaz, skutečný odkaz se může lišit)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.