ZTW Shark G2 60A SBEC Boat ESC User Manual

1. Úvod

This manual provides essential instructions for the proper installation, operation, and maintenance of your ZTW Shark G2 60A SBEC Electronic Speed Controller (ESC). Please read this manual thoroughly before using the product to ensure safe and optimal performance.

2. Klíčové vlastnosti

• Full waterproof design with reverse/bidirection function (forward and backward).
• Integrated aluminum water-cooling system for effective heat dissipation.
• Adjustable soft start function, adaptable to various RPM and pole motors.
• Supports high RPM and high pole count motors.
• Super smooth, accurate, and programmable throttle linearity and response.
• Comprehensive protection features: over-temperature, low voltage cut-off, and signal loss protection.
• Strong BEC output: 8A/5V continuous, with a peak of 10A.
• Programmable via programming card and transmitter.
• High efficiency with low resistance and low heat MOSFET and CPU.

3. Specifikace

4. Nastavení

Before initial use, ensure all connections are secure and correctly polarized. Connect the ESC to your motor, receiver, and battery according to your RC boat's wiring diagram. Pay close attention to the throttle calibration procedure outlined below.

4.1. Throttle Calibration

Throttle calibration is crucial for the first-time use or whenever the transmitter (TX) is changed. Follow these steps carefully:

1. For Reverse/Bi-Directional Function:
   • Set the throttle stick on your transmitter to the neutral position.
   • Power on the ESC. After hearing a beep, move the throttle stick to the MAX position.
   • After hearing another beep, move the throttle stick to the MINIMUM position.
   • Power off the ESC, then restart it. The calibration is complete.
2. For Forward-Only Function (No Reverse):
   • Set the throttle stick on your transmitter to the MAX position.
   • Power on the ESC. After hearing a beep, move the throttle stick to the MINIMUM position.
   • After hearing another beep, power off the ESC, then restart it. The calibration is complete.

5. Návod k obsluze

The ZTW Shark G2 60A SBEC ESC is designed for reliable performance in various aquatic RC applications. Ensure your motor and battery are compatible with the ESC's specifications before operation.

5.1. Aplikace

• Suitable for use with RC boat inrunner motors.
• Compatible with underwater thruster engines for RC bait tug boats, ROVs, and submarines.
• Applicable to any DIY project requiring a bi-directional function.

6. Údržba

While the ZTW Shark G2 60A SBEC ESC features a full waterproof design, proper care extends its lifespan. After each use in water, rinse the ESC with fresh water to remove any salt or debris, and allow it to dry completely before storage. Regularly inspect all wiring and connectors for signs of wear or corrosion. Ensure the water-cooling system is free from obstructions.

7. Řešení problémů

• Žádné napájení/žádná odezva: Check battery connections, ensure the battery is charged, and verify the ESC is correctly connected to the receiver.
• Motor se netočí: Re-perform throttle calibration. Check motor wire connections for proper phase. Ensure the motor is not seized.
• Přerušovaný provoz: Inspect all wiring for loose connections or damage. Check for signal interference. Ensure the BEC output is stable.
• Přehřívání: Verify the water-cooling system is functioning correctly and not obstructed. Ensure the motor is not overloaded or improperly geared.
• Neočekávané vypnutí: This may indicate low voltage cut-off or over-temperature protection activation. Check battery voltage a teplota ESC.

8. Záruka a podpora

ZTW and HAWK HOBBY provide a 100% free warranty for this ESC. For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.

For further assistance, please refer to the official ZTW webwebu nebo kontaktujte jejich zákaznickou podporu.