1. Konec produktuview
The LogiLink LPS402 Power Strip with Remote Control offers a convenient and energy-saving solution for managing your electronic devices. It features five protective contact sockets and integrated surge protection to safeguard your equipment. The included remote control allows you to switch devices on and off from a distance, and can even control a second compatible LogiLink power strip.
Image 1.1: The LogiLink LPS402 Power Strip, showing the five sockets, the main power plug, and the compact remote control.
Klíčové vlastnosti:
- 5 Protective Contact Sockets: Poskytuje ample connectivity for multiple devices.
- Funkce dálkového ovládání: Control the power strip from up to 20 meters away.
- Vícepásmové ovládání: The remote can control up to two LogiLink power strips (second strip sold separately).
- Integrovaná přepěťová ochrana: Protects connected devices from power surges, indicated by an LED light.
- Optimized Socket Layout: Sockets are angled at 45° for easier plug insertion.
- Increased Touch Protection: Sockets designed for enhanced safety.
- Stupeň krytí IP20: Protection against solid foreign objects greater than 12.5 mm and finger contact.
- Odolný kabel: 1.5 m H05VV-F 3G 1.5 mm² cable for reliable power delivery.
2. Pokyny k nastavení
2.1 Umístění
Place the power strip on a flat, stable surface, away from direct sunlight, heat sources, and moisture. Ensure there is adequate ventilation around the unit. Avoid covering the power strip with carpets or other materials that could impede heat dissipation.
Image 2.1: The power strip discreetly placed on the floor, demonstrating a typical installation scenario.
2.2 Connecting the Power Strip
- Ensure the power strip's main switch (if present) is in the OFF position.
- Insert the power strip's plug firmly into a standard 230V / 16A wall outlet.
- Plug your devices into the five protective contact sockets on the power strip.
- If applicable, switch the main power strip switch to the ON position.
2.3 Nastavení dálkového ovládání
The remote control is typically pre-paired with the power strip. If pairing is required or you wish to re-pair, follow these general steps:
- Ensure the power strip is plugged in and powered on.
- Locate the pairing button on the power strip (refer to the product diagram for exact location, usually a small button near the indicator lights).
- Press and hold the pairing button on the power strip for approximately 3-5 seconds until an indicator light (often green or blue) starts blinking.
- Within 10 seconds, press any ON button (e.g., ON-1) on the remote control.
- The indicator light on the power strip should stop blinking and remain solid, indicating successful pairing.
Image 2.2: A hand demonstrating the use of the remote control, highlighting its compact size and button layout.
3. Návod k obsluze
3.1 Základní ovládání zapnutí/vypnutí
Once the power strip is plugged in and devices are connected, use the remote control to manage power to the sockets.
- Stiskněte tlačítko ON-1 button on the remote to turn on all connected devices on the power strip.
- Stiskněte tlačítko VYP-1 button on the remote to turn off all connected devices on the power strip.
3.2 Controlling Multiple Power Strips
The remote control is designed to manage up to two LogiLink power strips. If you have a second compatible power strip (not included), you can pair it to the remote using the ON-2/OFF-2 buttons.
- To pair a second power strip, follow the pairing steps in Section 2.3, but press the ON-2 button on the remote during the pairing process.
- Po spárování použijte ON-2 button to turn on the second power strip and VYP-2 vypnout.
3.3 Surge Protection Indicator
The power strip features an LED indicator for surge protection. A green light typically indicates that the surge protection is active and functioning correctly. If this light is off or red, the surge protection may have been compromised by a significant power surge and the unit should be replaced.
4. Údržba
4.1 Čištění
- Před čištěním vždy odpojte prodlužovací kabel ze zásuvky.
- Use a soft, dry cloth to wipe down the exterior of the power strip and remote control.
- Do not use liquid cleaners, aerosols, or solvents, as these can damage the unit or pose an electrical hazard.
- Ensure no moisture enters the sockets or internal components.
4.2 Bezpečnostní opatření
- Do not overload the power strip beyond its maximum rated power (3680 W).
- Do not connect multiple power strips in series (daisy-chaining).
- Do not use the power strip in wet or damp prostředí.
- Uchovávejte mimo dosah dětí a domácích zvířat.
- Do not disassemble or attempt to repair the power strip or remote control. Refer to qualified personnel for service.
- Regularly inspect the power cord and plug for any signs of damage. If damaged, discontinue use immediately.
5. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Power strip does not turn on. | Not plugged in correctly; Wall outlet has no power; Main switch is OFF. | Ensure plug is fully inserted. Check wall outlet with another device. Turn main switch ON. |
| Dálkové ovládání nefunguje. | Remote battery is low or dead; Remote is out of range; Remote is not paired. | Replace remote battery. Move closer to the power strip (within 20m). Re-pair the remote control (see Section 2.3). |
| Devices connected to the power strip do not turn on/off. | Power strip is overloaded; Device itself is off or faulty. | Snižte celkový watttage of connected devices. Check if the individual device is powered on and functioning correctly. |
| Surge protection LED is off or red. | Surge protection has been activated/compromised. | The power strip may no longer provide surge protection. It is recommended to replace the unit. |
6. Technické specifikace
| Funkce | Specifikace |
|---|---|
| Číslo modelu | LPS402 |
| Celkové elektrické zásuvky | 5 x CEE 7/3 (Protection Contact) |
| svtage | 230 V |
| Proud | 16 A |
| Frekvence | 50 Hz |
| Maximální výkon | 3680 W |
| Specifikace kabelu | H05VV-F 3G 1.5 mm² |
| Délka kabelu | 1.5 m |
| Rozsah dálkového ovládání | Až 20 m (otevřené pole) |
| Hodnocení ochrany | IP20 |
| Barva | Bílý |
| Rozměry produktu | 16.42 x 2.2 x 1.65 palce |
| Hmotnost položky | 1.49 libry |
7. Informace o záruce
LogiLink products are manufactured with high-quality materials and undergo strict quality control. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official LogiLink webUschovejte si účtenku jako doklad o koupi pro případné reklamace.
8. Podpora
For further assistance, technical support, or inquiries regarding your LogiLink LPS402 Power Strip, please contact LogiLink customer service. Contact information can typically be found on the product packaging, the official LogiLink webwebu nebo prostřednictvím svého prodejce.
Výrobce: 2direct GmbH
Webmísto: Please refer to the official LogiLink website for up-to-date support information.