Uživatelská příručka k vektorovému síťovému analyzátoru NanoVNA-F V3.1

1. Úvod

The TZT NanoVNA-F V3.1 is a compact and versatile Vector Network Analyzer (VNA) designed for measuring RF circuits and antenna performance. It operates within a wide frequency range of 10KHz to 1.5GHz, making it suitable for various applications including amateur radio, antenna tuning, and general RF circuit analysis. This manual provides essential information for the proper setup, operation, and maintenance of your NanoVNA-F V3.1.

Figure 1: The NanoVNA-F V3.1 Vector Network Analyzer with its 4.3-inch IPS display showing S-parameter measurements.

2. Klíčové vlastnosti

• Široký rozsah měření: Covers 10KHz to 1.5GHz, with excellent dynamic range: >70dB for 10K-300MHz, >60dB for 300M-900MHz, and >40dB for 900M-1.5GHz.
• Vysokokapacitní baterie: Equipped with a 5000mAh battery for extended operation. Can also function as a mobile power source via its extended USB interface.
• Jasný displej: Features a 4.3-inch IPS TFT LCD with a resistive touch screen for clear data and curve visualization.
• Výkonné funkce: Capable of measuring S-parameters, Voltage Standing Wave Ratio (SWR), phase map, group delay, Smith chart, DELAY, POLAR, and LINEAR. Supports firmware upgrades via virtual U disk.
• PC and Android Phone Connectivity: Compatible with PC software (e.g., NanoVNA Saver) for data display and Touchstone (.snp) file export. Supports Android mobile phones for control.

3. Obsah balení

Po otevření balení se prosím ujistěte, že obsahuje všechny následující položky:

• NanoVNA-F V3.1 Vector Network Analyzer Unit
• Kabel USB typu C
• 2 x SMA Male to Male RG316 RF Cables
• Calibration Kit (OPEN, SHORT, LOAD)
• SMA Male to Female Adapters (various types)
• Stylus Pen

Figure 2: All components included in the NanoVNA-F V3.1 package.

4. Průvodce nastavením

4.1 Počáteční nabíjení

Before first use, fully charge the NanoVNA-F V3.1. Connect the provided USB Type-C cable to the device's USB-C port and the other end to a standard USB power adapter (5V, 1A recommended) or a computer's USB port. The charging indicator will show the charging status.

4.2 Zapnutí/vypnutí

Locate the power switch on the side of the device. Slide the switch to the "ON" position to power on the unit. To power off, slide the switch to the "OFF" position.

4.3 Connecting to a Device Under Test (DUT)

The NanoVNA-F V3.1 has two SMA ports: PORT 1 (S11) and PORT 2 (S21). Use the provided SMA cables and adapters to connect your DUT. For reflection measurements (S11), connect the DUT to PORT 1. For transmission measurements (S21), connect the input of the DUT to PORT 1 and the output to PORT 2.

Figure 3: Schematic representation of S-parameter measurement connections on the NanoVNA-F V3.1.

5. Provoz

5.1 Navigace v uživatelském rozhraní

The NanoVNA-F V3.1 features a resistive touch screen and a wheel button for navigation. Use the stylus or your finger to interact with the touch screen menus. The wheel button can be used for fine adjustments or menu selection in some modes.

5.2 Kalibrace

Calibration is crucial for accurate measurements. Perform a full two-port calibration (OPEN, SHORT, LOAD, THRU) for the desired frequency range before taking measurements. Access the calibration menu from the main screen.

1. Connect the OPEN standard to PORT 1 and perform the OPEN calibration.
2. Connect the SHORT standard to PORT 1 and perform the SHORT calibration.
3. Connect the LOAD standard to PORT 1 and perform the LOAD calibration.
4. Connect PORT 1 and PORT 2 directly using a THRU cable and perform the THRU calibration.
5. Uložte kalibrační data.

5.3 Režimy měření

The device supports various measurement modes, including:

• S11 (Reflection Coefficient): Measures the reflection characteristics of a device connected to PORT 1. Useful for SWR, Return Loss, and Smith Chart analysis.
• S21 (Transmission Coefficient): Measures the transmission characteristics between PORT 1 and PORT 2. Useful for gain/loss and phase measurements of filters, ampzáchranáři atd.
• SWR (poměr stojatých vln): Indicates the impedance match of an antenna or transmission line.
• Smith Chart: Graphical representation of complex impedance.
• Fáze: Displays the phase response of the DUT.
• Group Delay: Measures the time delay of signals through the DUT.

5.4 PC Software Connectivity

For advanced analysis and data logging, connect the NanoVNA-F V3.1 to a PC using the USB Type-C cable. Download and install compatible software like NanoVNA Saver. This software allows for larger display, detailed analysis, and export of Touchstone (.snp) files for use in other RF simulation tools.

6. Údržba

6.1 Čištění

K čištění zařízení používejte měkký, suchý hadřík. V případě odolných nečistot použijte lehceamp cloth can be used. Avoid using harsh chemicals or abrasive materials, as they may damage the screen or casing.

6.2 Skladování

When not in use, store the NanoVNA-F V3.1 in a cool, dry place, away from direct sunlight and extreme temperatures. Keep it in its original packaging or a protective case to prevent physical damage.

6.3 Péče o baterii

Chcete-li prodloužit životnost baterie, vyvarujte se častého úplného vybíjení. Pokud baterii skladujete delší dobu, nabijte ji přibližně na 50 % a dobíjejte ji každé několik měsíců.

7. Řešení problémů

8. Specifikace

Figure 4: Physical dimensions of the NanoVNA-F V3.1.

9. Záruka a podpora

Informace o záruce a technickou podporu naleznete v dokumentaci dodané s vaším nákupem nebo se obraťte přímo na výrobce. Uschovejte si doklad o koupi pro případ reklamace.

Pro tento model nebyla nalezena žádná oficiální produktová videa od prodejce.