Zavedení
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
Důležité bezpečnostní pokyny
- Read these instructions thoroughly before operating the module.
- Uschovejte si tyto pokyny pro budoucí použití.
- Dbejte všech varování na produktu a v návodu.
- Pro bezpečný provoz dodržujte všechny pokyny.
- Nepoužívejte toto zařízení v blízkosti vody nebo vlhkosti.
- Čistěte pouze suchým hadříkem.
- Neblokujte žádné ventilační otvory. Instalujte v souladu s pokyny výrobce.
- Neinstalujte v blízkosti zdrojů tepla, jako jsou radiátory, tepelné regulátory, kamna nebo jiná zařízení (včetně amplifikátory), které produkují teplo.
- Používejte pouze nástavce/příslušenství určené výrobcem.
- Veškerý servis svěřte kvalifikovanému servisnímu personálu. Je -li zařízení jakýmkoli způsobem poškozeno, je nutná údržba.
Nastavení
Instalace Eurorack
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- Vypnout: Always disconnect power from your Eurorack case before installing or removing any modules.
- Montáž: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- Připojení napájení: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- Zapnutí: Once securely mounted and connected, you can power on your Eurorack case.
Obrázek 1: Přední strana view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
Počáteční připojení
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
Obrázek 2: Detail view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
Návod k obsluze
Nadview ovládacích prvků
The 1027 module features a clear layout of controls for intuitive sequencing:
- Knoflík RATE: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- Přepínač ON/OFF: Toggles the sequencer's operation.
- STEP Buttons (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
Obrázek 3: Úhlové view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- Nastavit hodiny: Použijte HODNOTIT knoflík a NÍZKÁ/VYSOKÁ switch to set the desired tempo. Alternatively, connect an external clock to the CLK IN zvedák.
- Activate Steps: Stiskněte tlačítko KROK buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) nastavit objtage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: The POZIČNÍ BRÁNY will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- Start/Stop: Použijte ON/OFF switch to start and stop the sequence.
Pokročilé funkce
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: The KROK a RESETOVAT buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
Údržba
Čištění
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- Pro odolnou špínu lehceamphadřík vodou. Nepoužívejte agresivní chemikálie ani abrazivní čisticí prostředky.
- Do not allow any liquids to enter the module through jacks or openings.
Skladování
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Modul se nezapne. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
Specifikace
| Funkce | Detail |
|---|---|
| Název modelu | 1027 |
| Typ modulu | Taktovaný sekvenční řídicí modul |
| Série | Řada 2500 |
| Formát | Eurorack |
| Šířka | 16 HP |
| Hloubka | Not specified (typical Eurorack depth) |
| Spotřeba energie | Not specified (standard Eurorack +12V, -12V) |
| Vstupy | Clock In, External Pulse Width CV |
| Výstupy | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| Rozměry (V x Š x H) | 43 x 162 x 129 mm (přibližně 1.69 x 6.38 x 5.08 palce) |
| Hmotnost položky | 0.77 libry (přibližně 0.35 kg) |
| Technologie připojení | 3.5mm TS jack |
| Zdroj napájení | DC power supply (via Eurorack bus) |
Záruka
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
Popis záruky: Community. Musictribe. Com.
Podpora
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer webmísto:
- Behringer Official Webmísto
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.