Uživatelská příručka dálkového ovladače zvedacího křesla Okin

1. Konec produktuview

This manual provides instructions for the Okin 2 Button 5 Pin Power Recliner Switch Hand Control, designed as a universal replacement for lift chairs and electric sofas. It ensures seamless operation and control for your electric furniture.

Klíčové vlastnosti:

• Wired Recliner Switch Controller: Cable length 68.9 inches (175 cm).
• 5-pin round plug with a 90-degree L-shape connector.
• Universal compatibility with OKIN Single Motor electric furniture and most common brand recliner motors.
• Durable and ergonomic design for user comfort.

Figure 1: Okin 2 Button 5 Pin Power Recliner Hand Control with coiled cord and 5-pin connector.

Figure 2: The Okin remote control showing the full length of its extended cable.

2. Bezpečnostní informace

Please read and understand all safety instructions before using the product to prevent injury or damage.

• Do not exceed the maximum weight limit of the recliner.
• Ensure the recliner is properly grounded.
• Be cautious when operating the recliner to avoid pinching fingers or other body parts.
• Před zahájením jakékoli údržby nebo instalace vždy odpojte napájení.

3. Nastavení a instalace

The recliner chair controller is designed for easy installation. Follow these steps to replace your old or broken remote.

1. Identifikujte konektor: Before purchase and installation, carefully check the plug of your existing remote to ensure it matches the 5-pin round plug and 90-degree L-shape connector of this replacement.

Obrázek 3: Detail view of the 5-pin round plug connector.
2. Odpojit napájení: Unplug your recliner from the wall outlet to ensure safety during installation.
3. Locate Existing Connection: Find where your current remote control cable connects to the recliner's motor or control box.
4. Disconnect Old Remote: Carefully unplug the old remote control.
5. Připojení nového dálkového ovladače: Align the 5-pin round plug of the new Okin remote with the corresponding port on your recliner's motor or control box. Push firmly until it clicks into place.


Figure 4: The Okin remote control with its coiled cord and 5-pin connector, ready for installation.

6. Bezpečný kabel: Ensure the cable is not pinched or tangled.
7. Obnovit napájení: Plug your recliner back into the wall outlet.

4. Návod k obsluze

The Okin lift chair remote features a simple two-button interface for intuitive control of your recliner's movement.

Obrázek 5: Přední strana view of the Okin 2-button remote control.

• Up Button (Top Button): Press and hold the top button to raise the footrest and/or lift the chair to an upright or standing assist position. Release the button to stop movement.
• Down Button (Bottom Button): Press and hold the bottom button to lower the footrest and/or recline the chair to a seated or lying position. Release the button to stop movement.

The remote allows for precise control; release the button at any desired position to stop the chair's movement.

5. Údržba

To ensure the longevity and proper functioning of your Okin remote control, follow these simple maintenance guidelines:

• Čištění: Wipe clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the remote in water.
• Péče o kabely: Avoid kinking or excessively bending the cable. Ensure it is not caught under the recliner or furniture.
• Skladování: When not in use, store the remote in a safe place where it won't be damaged or stepped on.

6. Řešení problémů

If you experience issues with your Okin lift chair remote, try the following troubleshooting steps:

• Dálkové ovládání nereaguje:
  • Ensure the recliner is properly plugged into a working power outlet.
  • Check all cable connections, especially the 5-pin plug, to ensure they are secure and fully inserted.
  • Inspect the cable for any visible damage, cuts, or pinches.
• Přerušovaný provoz:
  • Verify that the 5-pin connector is clean and free of debris.
  • Gently wiggle the connector at the motor to see if it restores function, indicating a loose connection.
• Tlačítka nefungují:
  • Ujistěte se, že tlačítka nejsou zaseknutá nebo zablokovaná.
  • If only one button is not working, the remote may need replacement.

Pokud tyto kroky problém nevyřeší, kontaktujte prosím zákaznickou podporu.

7. Specifikace

Figure 6: Detail of the product label, showing model number (1.11-186.30) and power specifications (DC 29V 2A).

8. Záruka a podpora

Okin stands behind the quality of its products. While specific warranty details are not provided in this manual, customer satisfaction is guaranteed.

For any questions, issues, or support needs regarding your Okin Lift Chair Remote, please contact our customer service team. They are ready to help resolve any concerns you may have.

You can often find contact information on the product packaging or the official Okin webmísto.