KUIDAMOS DSO FNIRSI PRO Handheld Digital Oscilloscope User Manual

1. Konec produktuview

The KUIDAMOS DSO FNIRSI PRO is a portable digital oscilloscope designed for various measurement tasks. It features a 2.4-inch LCD display, a real-time sampling rate of up to 20MS/s, and an analog bandwidth of 5MHz. This device is equipped with a built-in 1200mAh rechargeable lithium battery, offering approximately 3 hours of continuous operation. It supports waveform storage and management, making it suitable for both maintenance and research and development applications.

Image 1.1: The DSO FNIRSI PRO Digital Oscilloscope, highlighting its 20MS/s samprychlostí přenosu a analogovou šířkou pásma 5 MHz.

Image 1.2: The oscilloscope's 2.4-inch HD LCD screen with 320 x 240 resolution for clear waveform display.

Obrázek 1.3: Přední a zadní strana views of the DSO FNIRSI PRO, illustrating its physical layout.

2. Obsah balení

Ověřte, zda jsou v balení obsaženy všechny níže uvedené položky:

• 1 x DSO FNIRSI PRO Digital Oscilloscope
• 1 x Matching Probe
• 1 x datový port USB
• 1 x Uživatelská příručka (tento dokument)

3. Počáteční nastavení

3.1 Nabíjení zařízení

Before first use, fully charge the oscilloscope. Connect the provided USB data line to the device's charging port and to a 5V/1A, 2A, 3A, or 4A USB power adapter. The built-in 1200mAh lithium battery can be charged continuously for approximately 3 hours.

3.2 Připojení sondy

Connect the matching probe to the BNC connector on the top of the oscilloscope. Ensure a secure connection by twisting the probe connector clockwise until it locks into place.

3.3 Zapnutí/vypnutí

To power on the device, press and hold the power button (usually located on the side or bottom) for a few seconds until the screen illuminates. To power off, press and hold the power button again until the device shuts down.

4. Návod k obsluze

4.1 Ovládací prvky a rozhraní

The oscilloscope features a user-friendly interface with several buttons for navigation and function control.

Image 4.1: Operating the DSO FNIRSI PRO, showing the placement of control buttons.

Obrázek 4.2: Detailní view of the oscilloscope's control panel.

• JÍDELNÍ LÍSTEK: Accesses the main menu for settings and functions.
• RUN/STOP: Starts or pauses waveform acquisition.
• AUTO: Automatically adjusts settings for optimal waveform display.
• TRIG: Adjusts trigger level.
• 50 %: Sets the trigger level to 50% of the waveform amplituda.
• AC/DC: Toggles between AC and DC coupling modes.
• 1x/10x: Sets the oscilloscope's input attenuation to match the probe's setting.
• MODE/OK: Confirms selections or changes modes.
• Šipky (nahoru, dolů, vlevo, vpravo): Procházení nabídek a úprava parametrů.

4.2 Probe Attenuation Settings

It is critical to match the probe's attenuation setting with the oscilloscope's input setting to ensure accurate measurements.

• Pro 1X measurement (0-40V): Set both the physical switch on the probe and the 1X/10X button on the oscilloscope to the 1X pozice.
• Pro 10X measurement (40-800V): Set both the physical switch on the probe and the 1X/10X button on the oscilloscope to the 10X pozice.

4.3 Measurement Modes and Triggering

The oscilloscope supports various trigger modes to stabilize waveform display:

• Singl: Captures a single waveform event and then stops.
• Normální: Captures a waveform only when a trigger condition is met.
• Auto: Continuously acquires waveforms, even without a trigger, but will trigger if a signal is present.

Použijte TRIG button and arrow keys to adjust the trigger level, which determines the voltage point at which the oscilloscope begins to acquire data.

4.4 Ukládání a správa průběhů

The device includes 16MB of built-in storage, capable of storing up to 500 waveform images. Use the file manager function to browse, view, and manage saved waveforms. This includes viewing detailed information, flipping through images, and deleting unwanted files.

Obrázek 4.3: Příkladamples of sine wave measurements at various frequencies.

Obrázek 4.4: Příkladamples of square, triangular, and sawtooth wave measurements.

5. Péče a údržba

5.1 Čištění

Zařízení otřete měkkým, suchým hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, protože by mohly poškoditasing nebo obrazovku. Před čištěním se ujistěte, že je zařízení vypnuté a odpojené od zdroje napájení.

5.2 Péče o baterii

Chcete-li prodloužit životnost baterie, vyvarujte se častého úplného vybíjení. Pokud zařízení skladujete delší dobu, nabijte jej přibližně na 50 % a dobíjejte jej každé několik měsíců.

5.3 Skladování

Store the oscilloscope in a cool, dry place, away from direct sunlight, extreme temperatures, and high humidity. Keep it protected from dust and physical impact.

6. Řešení problémů

• Issue: Abnormal measured data.
  Řešení: Check the probe's attenuation switch (1X or 10X) and ensure it matches the setting on the oscilloscope (using the 1X/10X button). If the probe is set to 10X and the oscilloscope is set to 1X, the device will not be damaged, but the data displayed will be incorrect.
• Issue: Device does not power on.
  Řešení: Ensure the battery is sufficiently charged. Connect the device to a power source using the USB data line and allow it to charge for at least 30 minutes before attempting to power it on again.
• Issue: Screen is blank or frozen.
  Řešení: Try performing a soft reset by pressing and holding the power button for an extended period (e.g., 10-15 seconds) until the device powers off, then power it back on. If the issue persists, ensure the battery is charged.

7. Technické specifikace

8. Záruka a zákaznická podpora

For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your purchase receipt as proof of purchase for any warranty claims.