PHYSEN Wireless Doorbell User Manual

Zavedení

Thank you for choosing the PHYSEN Wireless Doorbell. This manual provides detailed instructions for setting up, operating, and maintaining your doorbell system. Please read it carefully before use to ensure optimal performance and longevity of your device.

Obsah balení

Po otevření balení se prosím ujistěte, že jsou součástí balení všechny následující komponenty:

• 4 x Wireless Receivers
• 2 x Waterproof Push Buttons (Transmitters)
• Montážní šrouby
• Double-sided Adhesive Tapes
• Batteries (for transmitters)
• Mini User Manual (this document)

Nastavení a instalace

Umístění přijímače

Plug the receiver into a standard electrical outlet in your desired location. Ensure it is within the wireless range of the transmitter. The doorbell offers a working range of up to 400 meters (1300 feet) in open areas.

Vysílač Instalace

The push button (transmitter) is IP55 waterproof and weatherproof, suitable for outdoor installation. You can mount it using the provided screws or double-sided adhesive tape.

• Použití šroubů: Mark the desired location, drill pilot holes, and secure the transmitter with the screws.
• Použití lepicí pásky: Clean the surface thoroughly, peel off the backing from the double-sided tape, and firmly press the transmitter onto the surface.

Návod k obsluze

Párování přijímačů s vysílači

To set a separate sound for each receiver or pair a new transmitter, follow these steps:

1. Zapojte přijímač do elektrické zásuvky.
2. Briefly press the "Music" button on the receiver to select your desired ringtone.
3. Press and hold the volume button on the receiver for approximately 5-7 seconds until the blue light flashes. This indicates the receiver is in pairing mode. Note: The receiver will exit pairing mode automatically if no signal is received from the transmitter within 5 seconds.
4. Immediately press the transmitter button. You will hear the selected ringtone, confirming successful pairing.
5. Press the transmitter again for a final verification. If the melody plays, the pairing process is complete.

To set a different sound for a receiver triggered by another transmitter, simply select a new song on that receiver and repeat steps 1-4 with the new transmitter.

Reset/Clear Receiver Pairing Memory

To reset or clear the pairing memory of a receiver:

1. Zapojte přijímač do elektrické zásuvky.
2. Press and hold the "Music" button on the receiver for approximately 10 seconds until you hear a "ding" sound and the light flashes. This indicates that the receiver's memory has been reset/cleared.

Volume Adjustment and Chime Selection

The receiver offers multiple volume levels and 58 different chimes to choose from. Use the dedicated volume button to cycle through volume levels and the music button to select your preferred chime.

Údržba

Battery Replacement (Transmitter)

The transmitter uses a standard battery with an estimated 3-year lifespan. When the transmitter's performance degrades or it stops working, it's time to replace the battery.

1. Remove the protective film from the transmitter if present.
2. Use a small screwdriver (or the supplied tool) to open the back cover of the doorbell trigger.
3. Carefully remove the old battery and install a new battery of the appropriate size into the battery compartment, ensuring correct polarity.
4. Bezpečně zavřete zadní kryt.

Čištění

Otřete zvonkové jednotky měkkým, suchým hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla.

Odstraňování problémů

Specifikace

Záruka a podpora

PHYSEN offers a worry-free lifetime warranty for this product. A happy shopping experience is of utmost importance to us. Should you encounter any issues, we are happy to send a product replacement. Please contact our customer support for assistance.

For further support or inquiries, please visit the official PHYSEN webnebo kontaktujte svého prodejce.