Flysky FS-i6 6-Channel 2.4G AFHDS 2A RC Transmitter and iA6 Receiver Instruction Manual

1. Úvod

This manual provides detailed instructions for the setup, operation, and maintenance of your Flysky FS-i6 6-channel 2.4G AFHDS 2A Radio System, which includes the FS-i6 transmitter and the iA6 receiver. This system is designed for controlling various RC models such as fixed-wing aircraft, gliders, helicopters, and quadcopters. Please read this manual thoroughly before using the product to ensure safe and correct operation.

2. Bezpečnostní opatření

• Always operate your RC model in open areas, away from people, vehicles, and obstacles.
• Před každým použitím se ujistěte, že jsou všechny baterie plně nabité.
• Verify all control surfaces and motor functions are operating correctly before flight.
• Do not operate the radio system in adverse weather conditions (rain, strong winds, etc.).
• Chraňte vysílač a přijímač před vlhkostí a extrémními teplotami.
• Tento produkt není vhodný pro děti mladší 15 let bez dohledu dospělé osoby.

3. Obsah balení

Standardní balíček obsahuje následující komponenty:

• 1 x Flysky FS-i6 Transmitter
• 1 x Flysky FS-iA6 6CH Receiver
• 1 x zástrčka Bind

4. Konec produktuview

4.1 Uspořádání vysílače

The FS-i6 transmitter features a user-friendly layout with various controls and an LCD screen for easy monitoring and configuration.

Obraz: Přední view of the Flysky FS-i6 transmitter with key controls and features labeled, including joysticks, switches, trim buttons, and the LCD display.

The transmitter includes two main joysticks (left and right), various switches (VRA, VRB, Switch A, B, C, D), fine-tuning rods, and navigation buttons (UP, DOWN, OK, CANCEL, POWER, BIND KEY). The LCD screen displays real-time information such as model type, transmitter voltage, and receiver signal strength.

4.2 Přepnutí přijímačeview

The FS-iA6 receiver is a compact 6-channel receiver designed to work seamlessly with the FS-i6 transmitter. It features dual antennas for enhanced signal reception and stability.

Obraz: The Flysky FS-i6 transmitter shown alongside the compact FS-iA6 receiver, highlighting their relative sizes and design.

4.3 Instalace baterie

The FS-i6 transmitter requires four 1.5V AA batteries (not included) for operation. Ensure correct polarity when inserting the batteries.

Obraz: Detailní záběr view of the battery compartment on the back of the Flysky FS-i6 transmitter, showing the slots for four AA batteries.

5. Nastavení a vazba

5.1 Počáteční nastavení

Before powering on the transmitter, ensure all switches are in their up position and the throttle stick is in the lowest position. This prevents accidental motor activation.

5.2 Připojení přijímače

Connect the receiver to your RC model's Electronic Speed Controller (ESC) or power source. Ensure the bind cable is inserted into the B/VCC port on the receiver.

5.3 Postup vázání

Binding is the process of linking your transmitter to your receiver. Follow these steps to bind your FS-i6 transmitter with the iA6 receiver:

1. Ujistěte se, že je vysílač vypnutý.
2. Connect the bind plug to the B/VCC port on the iA6 receiver.
3. Power on the receiver (e.g., by connecting it to the ESC or a separate battery). The receiver's LED should flash rapidly.
4. While holding down the 'BIND KEY' button on the FS-i6 transmitter, power on the transmitter.
5. The transmitter's LCD screen should display 'RXBinding...' and then 'RX Bind OK' once successful.
6. Release the 'BIND KEY' button and power off both the transmitter and receiver.
7. Odstraňte spojovací zástrčku z přijímače.
8. Power on the transmitter first, then the receiver. The receiver's LED should now be solid, indicating a successful bind.
9. After successful binding, there is no need to insert a binding wire for normal use.

6. Provoz

6.1 Základní ovládací prvky

The FS-i6 transmitter offers 6 channels for controlling various functions of your RC model. The primary controls include:

• Levý joystick: Typically controls throttle and rudder.
• Pravý joystick: Typically controls aileron and elevator.
• Switches (A, B, C, D): Used for auxiliary functions such as landing gear, flaps, or flight modes.
• VR Knobs (VRA, VRB): Proportional controls for fine-tuning or additional functions.
• Ořezávací tlačítka: Used to adjust the neutral position of control surfaces.

6.2 Výběr režimu

The FS-i6 transmitter supports both Mode 1 (right throttle) and Mode 2 (left throttle) configurations. You can select your preferred mode through the transmitter's settings menu to match your flying style.

7. Specifikace

7.1 Transmitter Specifications (FS-i6)

7.2 Receiver Specifications (FS-iA6)

8. Řešení problémů

If you encounter issues with your Flysky FS-i6 system, consider the following common troubleshooting steps:

• Bez napájení: Check battery installation and ensure batteries are fully charged.
• No Link/Binding Issue: Re-perform the binding procedure carefully. Ensure the bind plug is correctly inserted and removed at the appropriate steps.
• Přerušovaný signál: Check receiver antenna placement. Ensure antennas are not obstructed or damaged. Avoid operating near strong interference sources.
• Nesprávná odpověď ovládacího prvku: Verify transmitter mode (Mode 1/2) matches your preference and model setup. Check servo connections to the receiver.
• Warning Messages on LCD: Refer to the specific warning message on the screen and consult the relevant section of this manual or Flysky's official support resources.

9. Údržba

Proper maintenance will extend the life and performance of your radio system:

• Keep the transmitter and receiver clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• Store the system in a cool, dry place when not in use. Remove batteries from the transmitter if storing for extended periods.
• Regularly inspect all cables and connectors for signs of wear or damage.
• Avoid exposing the LCD screen to direct sunlight for prolonged periods to prevent damage.