Zavedení
This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your iBELL 2058CS 18-inch 58CC Petrol Chain Saw. Please read all instructions thoroughly before assembly, operation, or maintenance to ensure personal safety and proper functioning of the equipment. Keep this manual for future reference.
Konec produktuview
Komponentní diagram
Zahrnuté položky
The standard package for the iBELL 2058CS includes the main chainsaw unit, an 18-inch guide bar, a saw chain, a fuel mixing bottle, and a basic tool kit for initial assembly and routine adjustments.
Nastavení
Vybalení a montáž
Carefully remove all components from the packaging. Inspect for any damage. Follow these steps to assemble the guide bar and saw chain:
- Open the side cover: Locate and open the side cover of the chainsaw to access the sprocket and guide bar mounting area.
- Install the inverted plate: Position the inverted plate correctly onto the chainsaw body.
- Install the saw chain: Carefully place the saw chain around the sprocket and guide bar, ensuring the cutting edges (knives) are facing the correct direction for cutting.
- Close the side cover and adjust chain tightness: Reattach the side cover. Adjust the chain tension so that the chain is snug against the guide bar but can still be pulled freely by hand. The recommended tightness allows for approximately 0.4-0.6 inches of play when pulled from the center of the guide bar.
- Lock the side cover: Securely fasten the side cover.
- Ověření instalace: Ensure all parts are securely fastened and the chain moves smoothly.
Směs paliva a oleje
The iBELL 2058CS is powered by a 2-stroke engine and requires a specific mixture of gasoline and 2T engine oil. Using an incorrect mixture can cause severe engine damage.
- Poměr míchání: Mix gasoline with 2T engine oil at a ratio of 25:1 (25 parts gasoline to 1 part 2T oil).
- Exampten: For 1 liter of gasoline, add 40 ml of 2T engine oil.
- Postup: Mix the fuel and oil in a separate, approved fuel container. Shake the mixture well before pouring it into the chainsaw's fuel tank. Do not pour 2T oil directly into the fuel tank without pre-mixing with gasoline.
Návod k obsluze
Bezpečnostní opatření
Operating a chainsaw can be dangerous. Always prioritize safety to prevent serious injury.
- Osobní ochranné prostředky (OOP): Always wear a safety helmet, eye protection (goggles or face shield), hearing protection, heavy-duty gloves, safety boots, and appropriate chainsaw protective clothing.
- Pracovní oblast: Ensure the work area is clear of bystanders, pets, and obstacles. Maintain a stable footing and balance.
- Předoperační kontrola: Before each use, inspect the chainsaw for loose parts, damage, proper chain tension, and sufficient fuel and chain oil levels. Ensure the chain brake is functional.
- Prevence zpětného rázu: Be aware of kickback risks. Avoid cutting with the tip of the guide bar. Always maintain a firm grip with both hands.
- Manipulace s palivem: Palivo doplňujte v dobře větraném prostoru s vypnutým a vychladlým motorem. Zabraňte rozlití paliva.
Startování motoru
The iBELL 2058CS features a large rope wheel for easier starting, reducing resistance.
- Place the chainsaw: Position the chainsaw on a firm, flat surface. Ensure the chain brake is engaged.
- Tlumivky: For a cold engine, pull the choke lever out fully.
- Zapalovací balónek (pokud je součástí výbavy): Několikrát stiskněte pumpičku, dokud nebude vidět palivo.
- Starting Handle: Hold the front handle firmly with one hand and pull the starter cord with the other hand in a smooth, steady motion until the engine fires (usually a few pulls).
- Nastavení sytiče: Once the engine fires, push the choke lever halfway in (or fully in, depending on the model's specific starting sequence).
- Final Start: Pull the starter cord again until the engine runs consistently.
- Zahřívání: Před sešlápnutím plynu nechte motor několik okamžiků zahřát.
Techniky řezání
Always maintain a balanced stance and firm grip. Engage the chain brake when moving between cuts or when the chainsaw is idling. Be mindful of the wood's tension and potential for kickback. The 20-inch bar is suitable for cutting diameters from 27 to 33 inches.
Zastavení motoru
To stop the engine, release the throttle trigger and push the ON/OFF switch to the 'OFF' position.
Údržba
Pravidelná údržba zajistí dlouhou životnost a bezpečný provoz vaší motorové pily.
- Chain Sharpening and Tensioning: Regularly check chain tension and adjust as needed. A dull chain increases effort and risk. Sharpen the chain according to manufacturer guidelines or have it professionally sharpened.
- Čištění: After each use, clean sawdust and debris from the guide bar groove, sprocket area, air filter, and cooling fins.
- Údržba vzduchového filtru: Clean the air filter regularly. A clogged air filter can reduce engine performance and increase fuel consumption.
- Kontrola zapalovací svíčky: Periodically inspect the spark plug for wear and proper gap. Replace if necessary.
- Automatic Chain Oiler: Ensure the automatic chain oiler is functioning correctly to lubricate the chain and guide bar.
- Skladování: When storing the chainsaw for extended periods, drain the fuel tank and run the engine until it stops to clear the carburetor. Clean the unit thoroughly and store it in a dry, secure location.
Odstraňování problémů
This section addresses common issues you might encounter with your iBELL 2058CS Petrol Chain Saw.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Motor nenastartuje | No fuel, incorrect fuel mixture, clogged fuel filter, fouled spark plug, incorrect choke setting, carburetor issues. | Check fuel level and mixture. Clean/replace fuel filter. Clean/replace spark plug. Adjust choke. If persistent, carburetor may need professional adjustment. |
| Motor nastartuje, ale zhasne | Incorrect idle speed, clogged air filter, fuel supply issues, carburetor adjustment. | Adjust idle screw. Clean air filter. Check fuel lines. Consult service for carburetor adjustment. |
| Řetěz neřeže efektivně | Tupý řetěz, nesprávné napnutí řetězu, opotřebovaná vodicí lišta. | Sharpen chain. Adjust chain tension. Inspect guide bar for wear and replace if necessary. |
| Nadměrný kouř z výfuku | Too much 2T oil in fuel mixture. | Ensure correct 25:1 fuel-to-oil ratio. Drain and refill with proper mixture if necessary. |
| Únik oleje | Loose oil cap, damaged oil lines, faulty oil pump. | Check oil cap. Inspect oil lines for damage. Contact service if oil pump is suspected. |
Specifikace
Technical specifications for the iBELL 2058CS Petrol Chain Saw:
| Funkce | Detail |
|---|---|
| Značka | IBELL |
| Číslo modelu | 2058CS |
| Zdroj napájení | Fuel Powered (2-Stroke Engine) |
| Zdvihový objem motoru | 58 CC |
| Koňská síla | 3.3 HP (2.5 kW) |
| Chain Length / Guide Bar | 18 palce |
| Rychlost bez zatížení | 3000 ± 200 ot./min |
| Maximální rychlost | 11500 ot./min |
| Hmotnost položky | 6.9 kg |
| Rozměry produktu (D x Š x V) | 54.4L x 35.7W x 28.1H centimetrů |
| Fuel Consumption Reduction | Up to 20% (compared to standard models) |
Záruka a podpora
Informace o záruce
The iBELL 2058CS Petrol Chain Saw comes with a Záruka 6 měsíců from the date of purchase. This warranty covers manufacturing or material defects as specified in the warranty card. Please note that the carburetor specifically has a 6-month warranty.
Důležité: Register your product online within one month (30 days) from the date of purchase to receive full warranty coverage. If the warranty card is missing, contact iBELL Customer Support within 10 days of purchase.
Zákaznická podpora
For any warranty-related issues, technical assistance, or product inquiries, please contact iBELL Customer Support:
- Bezplatné číslo: 1800-1034-090
- Přímá linka: +91-8589809292
- E-mail: icare@ibelltools.com
Manufacturer: STAR MACHINERY COMPANY LIMITED, NINGBO, PRC
