NEO Z-Wave Plus Smart Light Switch User Manual

1. Úvod

This manual provides comprehensive instructions for the installation, setup, operation, and maintenance of your NEO Z-Wave Plus Smart Light Switch. This intelligent device allows for remote control through a Z-Wave network and radio waves, integrating seamlessly into your smart home system. It requires a Z-Wave gateway controller to function.

The switch features two touch buttons, each capable of controlling an independent relay to turn devices on or off. Each gang supports a maximum of 16A. You can set timers for automated lighting and control the switch remotely.

2. Bezpečnostní informace

• VAROVÁNÍ: Nebezpečí úrazu elektrickým proudem. Instalaci by měl provádět pouze kvalifikovaný elektrikář nebo osoba s důkladnými znalostmi elektrických systémů.
• Disconnect power at the circuit breaker or fuse box before installation.
• Ujistěte se, že všechna elektroinstalace jsou bezpečná a splňují místní elektrotechnické předpisy.
• Do not exceed the maximum load rating of 16A per gang.
• Toto zařízení je určeno pouze pro vnitřní použití.
• Chraňte před vodou a nadměrnou vlhkostí.

3. Konec produktuview

The NEO Z-Wave Plus Smart Light Switch features a sleek touch panel design with integrated indicator lights for status feedback.

Obrázek 3.1: Přední strana view of the NEO Z-Wave Plus Smart Light Switch, showing two touch-sensitive circles.

Obrázek 3.2: Strana view illustrating the thin 1mm tempered glass panel of the switch, highlighting its anti-shock and bending strength properties.

Figure 3.3: Detailed technical drawing showing the dimensions (120mm x 74mm x 37mm) and internal components of the smart light switch.

4. Instalace

Before beginning installation, ensure the power is OFF at the circuit breaker. This device is designed for in-wall installation in a standard electrical box.

4.1 Schéma zapojení

The switch requires Live (Line), Load, and Neutral connections. A ground wire should also be connected for safety.

Figure 4.1: Simplified wiring diagram showing connections for Live, Load, and Neutral wires. Consult a qualified electrician if unsure.

4.2 kroky instalace

1. Vypnout napájení: Vyhledejte jistič ovládající umístění spínače a vypněte jej. Ověřte, zda je napájení vypnuto pomocí regulátoru hlasitosti.tage tester.
2. Demontáž starého spínače: Carefully remove the existing wall plate and switch from the electrical box. Disconnect the wires.
3. Wire the NEO switch: Connect the wires to the corresponding terminals on the NEO Z-Wave Plus Smart Light Switch.
   • Connect the Live (Line) wire to the 'L' terminal.
   • Connect the Load wire(s) to the 'L1' and 'L2' terminals (for 1st and 2nd gang respectively).
   • Připojte nulový vodič ke svorce „N“.
   • Connect the Ground wire to the ground screw in the box.

   Note: Some users have reported issues with terminal design and mounting. Ensure wires are neatly tucked into the electrical box to prevent interference with the mounting plate. Spacers or washers may be needed between the back plate and the wall if the main unit clips do not seat properly.

4. Namontujte spínač: Secure the switch into the electrical box using the provided screws.
5. Attach faceplate: Snap the glass faceplate onto the switch module.
6. Obnovení napájení: Znovu zapněte napájení jističem.

5. Z-Wave Network Setup

The NEO Z-Wave Plus Smart Light Switch must be included (paired) into a Z-Wave network to enable smart control features. It works with most Z-Wave hubs, including SmartThings, Vera, Fibaro, HomeSeer, Iris, and Aeotec.

5.1 Inclusion (Pairing)

1. Ensure your Z-Wave gateway controller is in inclusion mode (refer to your gateway's manual for specific instructions).
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm inclusion mode.
3. The gateway will detect and add the device. Once successfully included, the indicator light will stop flashing and show its normal status.

5.2 Exclusion (Unpairing)

1. Ensure your Z-Wave gateway controller is in exclusion mode.
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm exclusion mode.
3. The gateway will remove the device from the network.

6. Návod k obsluze

The NEO Smart Light Switch offers both manual touch control and remote Z-Wave control.

6.1 Ruční ovládání

Simply touch the circular icons on the glass panel to toggle the connected lights or devices ON/OFF.

Figure 6.1: Indicator lights on the touch panel. When power is ON, the LED is red. When power is OFF, the LED is blue.

6.2 Remote Control via Z-Wave Hub

Once paired with your Z-Wave hub, you can control the switch remotely using your hub's mobile application or other integrated smart home systems. This allows for scheduling, scene creation, and control from anywhere.

Figure 6.2: Illustration of a smartphone app controlling the smart light switch through a Z-Wave hub, enabling remote management.

7. Údržba

The NEO Z-Wave Plus Smart Light Switch requires minimal maintenance.

• Čištění: To clean the glass panel, gently wipe it with a soft, damp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla, protože by mohly poškodit povrch.
• Aktualizace firmwaru: Check your Z-Wave hub's documentation for information on potential firmware updates for connected devices.

8. Řešení problémů

If you encounter issues with your NEO Z-Wave Plus Smart Light Switch, refer to the following common problems and solutions:

9. Specifikace

10. Záruka a podpora

For warranty information and technical support, please refer to the documentation included with your product packaging or visit the official NEO webmísto. Uschovejte si doklad o koupi pro případ záručních reklamací.