Návod k použití

Zavedení

This manual provides essential information for the safe and proper installation, operation, and maintenance of your Bryant 9450FR Industrial Grade 50 Amp NEMA 14-50 Receptacle. Please read all instructions carefully before beginning any work.

Bezpečnostní informace

VAROVÁNÍ: Risk of electric shock or fire. Installation must be performed by a qualified electrician in accordance with all national and local electrical codes.

• Always disconnect power at the circuit breaker or fuse box before installing or servicing this receptacle.
• Ověřte, že je napájení vypnuto pomocí voltage testeru, než se dotknete jakýchkoli vodičů.
• Zajistěte správné uzemnění, abyste zabránili úrazu elektrickým proudem.
• Nepřekračujte stanovený objemtage a amperage ratings of the receptacle.
• Use only appropriate tools and personal protective equipment (PPE).

Obsah balení

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny a nepoškozené.

• Bryant 9450FR NEMA 14-50 Receptacle
• Montážní šrouby (obvykle součástí balení)
• Pokyny k použití (tato příručka)

Image: The Bryant 9450FR NEMA 14-50 Receptacle shown with the included mounting screws in clear plastic bags.

Nastavení (instalace)

This receptacle is designed for flush mounting. Follow these steps for proper installation:

1. Připravte si místo: Ensure you have a suitable electrical box (e.g., 4x4 square box with a 2-gang mud ring or a single-gang box with appropriate adapter) that can accommodate the receptacle and wiring.
2. Vypnout napájení: Locate the circuit breaker for the circuit you will be working on and switch it to the OFF position. Verify with a voltage tester that no power is present at the wires.
3. Odizolování drátů: Carefully strip approximately 3/4 inch (19mm) of insulation from the ends of the supply wires. For 14-50R, you will typically have two hot wires (black/red), one neutral wire (white), and one ground wire (green/bare copper).
4. Připojit dráty: The Bryant 9450FR features clearly marked terminals.
   • Připojte ZELENÝ or bare copper ground wire to the terminal marked "GREEN" (grounding screw).
   • Připojte BÍLÝ neutral wire to the terminal marked "WHITE" (neutral screw).
   • Spojte oba HORKÝ wires (black and red) to the remaining two terminals marked "XXX" (line screws).
   

   Obrázek: Zadní view of the receptacle showing the screw terminals labeled for proper wire connection (White, Green, and two Hot).

5. Zabezpečená připojení: Tighten all terminal screws firmly to ensure good electrical contact. Tug gently on each wire to confirm it is securely fastened.
6. Montážní zásuvka: Carefully fold the wires into the electrical box. Align the receptacle with the mounting holes in the electrical box and secure it using the provided mounting screws. Do not overtighten.
7. Install Faceplate (Not Included): Once the receptacle is securely mounted, install a compatible NEMA 14-50 faceplate (sold separately) over the receptacle.
8. Obnovit napájení: Go back to the circuit breaker or fuse box and switch the power back ON.

Obrázek: Přední strana view of the Bryant 9450FR NEMA 14-50 Receptacle, ready for faceplate installation.

Návod k obsluze

The Bryant 9450FR NEMA 14-50 Receptacle is designed for use with NEMA 14-50 compatible plugs. To operate:

1. Ensure the appliance or device you intend to connect is rated for 125/250V and does not exceed 50 Amps.
2. Align the prongs of the NEMA 14-50 plug with the corresponding slots on the receptacle.
3. Firmly insert the plug into the receptacle until it is fully seated.
4. To disconnect, firmly grasp the plug and pull it straight out from the receptacle. Do not pull by the cord.

Údržba

The Bryant 9450FR receptacle requires minimal maintenance. Regular inspection is recommended:

• Periodically inspect the receptacle for any signs of damage, such as cracks, discoloration, or loose connections.
• Ensure the faceplate is securely attached.
• Keep the receptacle clean and free of dust or debris. Use a dry cloth for cleaning. Do not use liquid cleaners.
• If any damage is observed, disconnect power to the circuit and have the receptacle inspected and replaced by a qualified electrician.

Odstraňování problémů

If you experience issues with your receptacle, consider the following common troubleshooting steps:

For issues not covered here, or if problems persist, contact a qualified electrician.

Specifikace

Záruka

This Bryant product is manufactured to high-quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the manufacturer's official webUschovejte si doklad o koupi pro případ reklamace.

Podpora

For technical assistance or further inquiries, please contact the manufacturer or your authorized distributor. Always provide the model number (9450FR) when seeking support.

Výrobce: Bryant (a Hubbell brand)

Webmísto: www.hubbell.com/bryant/en