Daytona 3 Ton Low Profile Podlahový Jack

Zavedení

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Daytona 3 Ton Low Profile Floor Jack. Designed for heavy-duty use, this jack features a low-profile design to fit under most vehicles and a rapid pump system for quick lifting. Please read this manual thoroughly before use to ensure proper handling and to prevent injury or damage.

Figure 1: The Daytona 3 Ton Low Profile Floor Jack in orange, showcasing its robust design and low-profile podvozek.

Bezpečnostní informace

VAROVÁNÍ: Nedodržení těchto pokynů může mít za následek vážné zranění nebo poškození majetku.

• Always use jack stands to support the vehicle after lifting. Never rely solely on the floor jack for support.
• Ensure the jack is on a hard, level surface capable of supporting the load. Avoid using on asphalt or soft ground.
• Center the load on the saddle. Off-center loads can cause the jack to tip.
• Do not exceed the rated capacity of 3 tons.
• Udržujte ruce a nohy v dostatečné vzdálenosti od pohyblivých částí.
• Používejte vhodné osobní ochranné prostředky (OOP), jako jsou ochranné brýle a rukavice.
• Do not modify the jack or use it for purposes other than lifting vehicles.
• Before lowering, ensure all tools and personnel are clear from under the vehicle.

Komponenty skončilyview

Familiarize yourself with the main components of your floor jack:

• Sedlo: The circular pad that contacts the vehicle's lift point. It is rotating and removable to adapt to lift accessories.
• Lift Arm: The main arm that raises and lowers the saddle.
• Zacházet s: Used for pumping the jack and controlling the lowering mechanism.
• Vypouštěcí ventil: Located at the base of the handle, controls the lowering speed.
• Přední kola: Fixed wheels at the front of the jack.
• Rear Swivel Casters: Ball bearing casters at the rear for 360° mobility.
• Hydraulická jednotka: Contains the dual piston hydraulic system for rapid lifting.

Obrázek 2: Pohled shora dolů view of the Daytona 3 Ton Floor Jack, highlighting the saddle, handle connection, and the "3 TON LOW PROFILE HIGH PERFORMANCE" label.

Nastavení

1. Rozbalení: Opatrně vyjměte zvedák z obalu. Zkontrolujte, zda nedošlo k poškození při přepravě.
2. Sestava rukojeti: Insert the handle into the handle socket at the rear of the jack. Secure it according to the instructions provided in the separate assembly sheet (if applicable).
3. Odvzdušnění (odvzdušnění): Before first use, or if the jack has been stored horizontally, it may be necessary to purge air from the hydraulic system.
   • Otočte vypouštěcí ventil proti směru hodinových ručiček, abyste jej zcela otevřeli.
   • Rychle pumpujte rukojetí 10–15krát bez zátěže.
   • Otočením vypouštěcího ventilu ve směru hodinových ručiček jej zavřete.
   • Test the jack's lifting and lowering function. Repeat if necessary.

Návod k obsluze

Zvedání vozidla:

1. Připravte vozidlo: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
2. Umístění zvedáku: Locate the vehicle manufacturer's recommended lifting points. Slide the jack under the vehicle, ensuring the saddle is centered directly under the lifting point.


Figure 3: The Daytona 3 Ton Floor Jack correctly positioned under a vehicle's frame, ready for lifting. Note the low profile allowing access.

3. Zvedněte vozidlo: Turn the release valve clockwise until it is firmly closed. Pump the handle up and down to raise the vehicle to the desired height. The dual piston system provides rapid lifting.
4. Zajištění pomocí zvedáků: Immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Spouštění vozidla:

1. Prepare for Lowering: Ensure the area around and under the vehicle is clear of obstructions and personnel.
2. Mírně zvedněte: If the vehicle is on jack stands, position the floor jack under the original lifting point and raise the vehicle slightly to clear the jack stands.
3. Demontáž podpěr: Opatrně vyjměte podpěry zvedáku.
4. Spusťte vozidlo dolů: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Do not open the valve too quickly, as this can cause the vehicle to drop rapidly.
5. Odstraňte Jacka: Once the vehicle is fully on the ground, remove the floor jack.

Údržba

• Mazání: Periodically lubricate all moving parts with light machine oil. Check the wheels and casters for smooth operation.
• Hydraulická kapalina: Check the hydraulic fluid level every 6 months. To check, lower the jack completely, remove the oil filler plug, and ensure the fluid is level with the bottom of the filler hole. Use only high-quality hydraulic jack oil. Do not use brake fluid or motor oil.
• Čištění: Keep the jack clean and free of dirt, grease, and debris. This helps prevent corrosion and ensures smooth operation.
• Skladování: Store the jack in a clean, dry place with the ram fully retracted to prevent rust and extend seal life.
• Inspekce: Před každým použitím zkontrolujte zvedák, zda nevykazuje známky poškození, netěsností nebo opotřebení. Poškozený zvedák nepoužívejte.

Odstraňování problémů

Specifikace

Záruka a podpora

For warranty information or technical support, please refer to the official Daytona webnebo se obraťte na jejich zákaznický servis. Uschovejte si doklad o koupi pro případ reklamace.

Online podpora: Navštivte Daytona Store on Amazon pro informace o produktech a zdroje podpory.