Zavedení
The BWT Aquameter is an accessory designed to monitor the water flow through your BWT filter cartridge. It features an LCD display and two buttons for easy programming and tracking of water volume, indicating when filter replacement is recommended. This manual provides detailed instructions for the proper installation, operation, and maintenance of your Aquameter.
Důležité bezpečnostní informace
- Read all instructions thoroughly before installing or operating the device.
- Udržujte zařízení mimo dosah dětí.
- While the device is waterproof, do not immerse it in water. It is designed to withstand splashes and moisture, but not submersion.
- Use only the specified battery type: CR2032.
- Použité baterie zlikvidujte v souladu s místními předpisy.
Obsah balení
Ověřte, zda jsou v balení přítomny všechny položky:
- BWT 3/8" Aquameter with LCD Display
- 1x baterie CR2032
Nastavení
1. Instalace baterie
The Aquameter requires one CR2032 battery for operation.
- Locate the battery compartment on the back of the Aquameter.
- Opatrně otevřete kryt bateriového prostoru.
- Insert the CR2032 battery with the positive (+) side facing up, ensuring it is seated correctly.
- Bezpečně zavřete kryt prostoru pro baterie.
Image: The BWT Aquameter, illustrating its compact design and the location for battery insertion.
2. Mounting to Filter Head
The Aquameter is designed to be fitted directly onto a compatible BWT filter head.
- Ensure your BWT filter head is already installed according to its specific instructions.
- Align the Aquameter with the designated connection points on the filter head.
- Securely attach the Aquameter, ensuring a tight and leak-free connection. Refer to your filter head's manual for precise attachment methods.
3. Počáteční programování
After battery installation, the LCD display will activate. You must program the device with your specific water hardness and the filter's capacity.
- Stiskněte a podržte SOUBOR tlačítko pro vstup do programovacího režimu.
- Použijte MODE button to cycle through the available settings, such as water hardness (e.g., dH, ppm) and filter capacity (e.g., gallons, liters).
- Použijte SOUBOR button to adjust the values for each setting.
- Confirm your selections by pressing SOUBOR again or by waiting for the display to automatically exit programming mode.
- The meter will then display the programmed total volume and begin counting down as water flows through the system.
Návod k obsluze
LCD displej Overview
The LCD display provides real-time information about your filter's status:
- Remaining Volume: Shows the volume of water (in gallons or liters) that can still pass through the filter before replacement is needed.
- Flow Indicator: A symbol or animation may appear when water is actively flowing through the Aquameter.
- Indikátor baterie: Zobrazuje aktuální stav baterie.
Monitoring Water Flow
The Aquameter automatically tracks the volume of water passing through the filter. The displayed remaining volume will decrease as water is used.
Filter Replacement Indication
When the remaining volume counts down to 0, it is recommended to replace your filter cartridge. The device may also display a specific alert or icon to clearly indicate that replacement is due.
Funkce tlačítek
The Aquameter features two primary buttons for interaction:
- Tlačítko SET: Used to enter programming mode, confirm selections, and reset certain parameters.
- Tlačítko MODE: Used to cycle through display modes or adjust values during programming.
Údržba
Čištění
The Aquameter can be cleaned by wiping its exterior with a soft, damp hadříkem. Nepoužívejte abrazivní čisticí prostředky, rozpouštědla ani neponořujte zařízení do vody.
Výměna baterie
When the battery indicator on the LCD display shows low power, replace the CR2032 battery by following the steps outlined in the "Battery Installation" section.
Výměna filtrační vložky
Replace your filter cartridge as indicated by the Aquameter (when the remaining volume reaches 0). Always refer to your specific filter cartridge's instructions for proper replacement procedures.
Odstraňování problémů
If you encounter issues with your BWT Aquameter, refer to the table below for common problems and their solutions.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Displej je prázdný nebo se nezapíná. | Vybitá nebo nesprávně nainstalovaná baterie. | Zkontrolujte instalaci baterií. V případě potřeby vyměňte baterii CR2032. |
| Volume is not counting down. | Incorrect installation; no water flow; programming error. | Ensure the Aquameter is securely attached to the filter head. Verify that water is flowing through the system. Re-program the device with correct settings. |
| Inaccurate volume readings. | Incorrect water hardness or filter capacity programmed. | Re-program the device with the correct water hardness and filter capacity settings according to your filter cartridge specifications. |
Specifikace
Technická data
- Model: BWT812195
- Značka: BWT
- Typ displeje: LCD
- Zdroj napájení: 1x baterie CR2032
- Speciální funkce: Vodotěsný
- Vnější materiál: Plast
- Péče o produkt: Dočista vyčistit
- Hmotnost položky: Přibližně 10 liber (4.5 kg)
- Vnitřní/venkovní použití: Venkovní
Záruka a zákaznická podpora
For detailed warranty information, technical assistance, or customer support, please contact BWT customer service or the authorized retailer from whom you purchased this product. Please retain your proof of purchase for any warranty claims.
- Výrobce: BWT
- Číslo dílu výrobce: OM-L1NC-16YQ