MICHELIN 12294A

Michelin 12294A Digital Programmable Tire Pressure Gauge

Uživatelská příručka

Zavedení

Thank you for choosing the Michelin 12294A Digital Programmable Tire Pressure Gauge. This device is designed for accurate and convenient measurement of tire pressure, ensuring optimal vehicle performance and safety. Please read this manual thoroughly before use.

Obsah balení

  • 1 x Michelin 12294A Digital Programmable Tire Pressure Gauge
  • 2 x Lithium-metal batteries (pre-installed or included)
Michelin 12294A Digital Programmable Tire Pressure Gauge

Image: The Michelin 12294A Digital Programmable Tire Pressure Gauge, showing its digital display and control buttons.

Nastavení

Instalace baterie

The device requires 2 Lithium-metal batteries. These are typically included or pre-installed. If replacement is needed:

  1. Locate the battery compartment cover, usually on the back or side of the unit.
  2. Otevřete kryt.
  3. Vložte baterie se správnou polaritou (+/-).
  4. Bezpečně zavřete kryt bateriového prostoru.

Zapnutí/vypnutí

  • Pro zapnutí stiskněte Tlačítko napájení (often marked with a circle and vertical line symbol).
  • The backlit LCD display will illuminate.
  • Zařízení se po určité době nečinnosti automaticky vypne, aby se šetřila baterie.

Návod k obsluze

Měření tlaku v pneumatikách

  1. Pro co nejpřesnější odečet se ujistěte, že je pneumatika studená.
  2. Sejměte krytku ventilku z pneumatiky.
  3. Press the nozzle of the gauge firmly onto the tire valve stem. A good seal is crucial for an accurate reading.
  4. The digital display will show the tire pressure.
  5. Remove the gauge from the valve stem. The reading will hold on the display for a short period.
  6. Vyměňte uzávěr ventilu.
Michelin 12294A Tire Pressure Gauge in use on a car tire

Image: The Michelin 12294A gauge being used to measure pressure on a car tire valve.

Změna měrných jednotek

The gauge supports measurements in PSI, KPA, BAR, and kg/cm². To cycle through units, press the Tlačítko jednotky (often the same as the power button or a dedicated button). The current unit will be displayed on the screen.

Programming Tire Pressures

This gauge can be programmed with target front and rear tire pressures for up to two vehicles. Refer to your vehicle's owner's manual or the sticker on the driver's side door jamb for recommended tire pressures.

  1. With the gauge powered on, press and hold the Tlačítko programu (often an arrow button or a dedicated 'SET' button) until the programming mode is activated.
  2. Použijte Tlačítka se šipkami nahoru/dolů to adjust the target pressure for the front tires of Vehicle 1.
  3. Stiskněte tlačítko Tlačítko programu again to switch to the rear tires of Vehicle 1, then adjust.
  4. Repeat the process for Vehicle 2 if desired.
  5. The gauge will save the settings automatically after a few seconds of inactivity or by pressing the Program button to exit.
Close-up of Michelin 12294A display showing current and target PSI

Obrázek: Detailní záběr view of the gauge's digital display, showing current pressure and programmable target pressure settings.

Using the Integrated Flashlight

The gauge features an integrated flashlight to assist in locating the tire valve in low-light conditions. To activate the flashlight, press the Tlačítko svítilny (refer to device markings, often combined with another function or a dedicated button).

Using the Bleed Valve

If a tire is over-inflated, the built-in bleed valve allows for controlled release of air. While the gauge is attached to the valve stem and displaying pressure, gently press the Bleed Valve button (if present, often a small button near the nozzle) to release air until the desired pressure is reached.

Údržba

  • Čištění: Wipe the gauge with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water.
  • Skladování: Store the gauge in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Výměna baterie: If the display becomes dim or the device does not power on, replace the batteries. Dispose of old batteries according to local regulations.

Odstraňování problémů

Problém Možná příčina Řešení
No display/Device does not power on Vybité nebo nesprávně vložené baterie. Zkontrolujte polaritu baterií nebo je vyměňte.
Nepřesné čtení Poor seal with valve stem; tire not cold; gauge malfunction. Ensure a firm, airtight seal. Measure when tires are cold. If issues persist, contact support.
Air leaks when measuring Gauge not properly seated on valve stem. Press the gauge firmly and squarely onto the valve stem.

Specifikace

Značka MICHELIN
Číslo modelu 12294A
Název modelu Tlakoměr
Hmotnost produktu 100 g
Rozměry produktu 9.3 x 3.3 x 2 cm
Baterie 2 lithium-metal (součástí balení)
Měrné jednotky PSI, kPA, BAR, kg/cm²
Přesnost +/- 1 %
Materiál Metal core, ribbed plastic exterior
Typ závitu Schrader

Záruka a podpora

This Michelin product is manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Michelin automotive accessories webUschovejte si doklad o koupi pro případ reklamace.

© 2023 Michelin. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.