Luceco EFDGUIPPC-01

Luceco LED svítidlo IP65 s protipožární paticí GU10, leštěný chrom, návod k obsluze

Model: EFDGUIPPC-01

1. Úvod

This manual provides essential instructions for the safe installation, operation, and maintenance of your Luceco LED IP65 Fire Rated GU10 Downlight. Please read this manual thoroughly before installation and retain it for future reference. This downlight is designed for recessed ceiling installation and features an IP65 rating, making it suitable for areas where protection against water jets is required, such as bathrooms (Zone 1 and 2) and outdoor sheltered areas. It also incorporates a fire-rated housing for enhanced safety.

Luceco LED IP65 Fire Rated GU10 Downlight, polished chrome finish, illuminated.

Obrázek 1: Luceco LED IP65 Fire Rated GU10 Downlight (Polished Chrome)

Tento obrázek ukazuje přední stranu view of the Luceco LED IP65 Fire Rated GU10 Downlight. It features a polished chrome finish bezel with a central light source, designed for a sleek, modern appearance when installed in a ceiling.

2. Bezpečnostní informace

  • Profesionální instalace: Installation must be carried out by a qualified electrician in accordance with national wiring regulations and local building codes.
  • Odpojení napájení: Always ensure the main power supply is switched off at the consumer unit/fuse box before commencing any installation, maintenance, or bulb replacement.
  • Uzemnění: This downlight has a metal casing and requires proper earthing. Ensure the earth wire is securely connected.
  • Typ žárovky: Use only GU10 LED or halogen bulbs up to a maximum of 35W. The downlight is supplied without a bulb.
  • Bulb Dimensions: Ensure the GU10 bulb length does not exceed 50-60mm to fit correctly within the fire-rated housing.
  • Stupeň krytí IP65: The IP65 rating provides protection against dust ingress and low-pressure water jets. Ensure all seals are correctly seated during installation to maintain this rating.
  • Požární hodnocení: This downlight is fire-rated, designed to maintain the integrity of the ceiling's fire resistance. Do not modify the housing.
  • Větrání: Ensure adequate clearance around the downlight in the ceiling void as per manufacturer guidelines and local regulations to prevent overheating.
  • Poškození: Do not install if the product or any components are damaged.

3. Obsah balení

Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny a nepoškozené.

  • 1 x Luceco LED IP65 Fire Rated GU10 Downlight (Polished Chrome finish)
  • Návod k použití
  • Note: GU10 bulb is not included and must be purchased separately.

4. Specifikace

ZnačkaLuceco
Číslo modeluEFDGUIPPC-01
Rozměry produktu9.63 x 12.48 x 12 cm
Hmotnost280 gramů
MateriálKov
DokončitLeštěný Chrome
StylFixed Fire Rated GU10 Downlight / IP65 Rated
Lamp DržákGU10
Max Wattage35W (žárovka není součástí balení)
Hodnocení IPIP65 (Suitable for bathrooms Zone 1 & 2)
Ceiling Cut-out Diameter72 mm (přibližně)

5. Nastavení a instalace

Důležité: Installation should only be performed by a qualified electrician. Ensure power is disconnected before starting.

  1. Připravte si strop:

    Using an appropriate hole saw, cut a circular opening in the ceiling with a diameter of approximately 72mm. Ensure there is sufficient vertical clearance in the ceiling void for the downlight's housing (approx. 12cm depth).

  2. Zapojení:

    The downlight features tool-free access and loop-in loop-out terminals. Carefully strip the insulation from the live, neutral, and earth wires of your mains supply. Insert the wires into the corresponding push-fit terminals (Live, Neutral, Earth). Ensure a secure connection for all wires, especially the earth wire, due to the metal casing.

    Zadní view of Luceco downlight showing wiring terminals and spring clips.

    Obrázek 2: Downlight Rear View s kabelovými svorkami

    This image displays the rear of the downlight, highlighting the black cylindrical housing, the spring-loaded clips for ceiling retention, and the push-fit wiring terminals for electrical connection.

  3. Insert GU10 Bulb:

    Before inserting the downlight into the ceiling, insert a GU10 bulb (not supplied) into the lamp holder. Align the two pins of the GU10 bulb with the slots in the lamp holder, push gently, and twist clockwise to secure it. Ensure the bulb length is within the 50-60mm limit.

  4. Install Downlight into Ceiling:

    Fold back the spring clips on the sides of the downlight housing. Carefully push the downlight into the prepared ceiling opening until the spring clips engage and hold the fitting securely in place. Ensure the rubber gasket is properly seated to maintain the IP65 rating.

  5. Attach Bezel:

    The polished chrome bezel is secured by a twist mechanism. Align the bezel with the main housing and twist clockwise until it clicks securely into place. Ensure it is flush with the ceiling surface.

    Polished chrome bezel for the downlight.

    Obrázek 3: Polished Chrome Bezel

    This image shows the separate polished chrome bezel, which is the visible trim of the downlight once installed. It features a smooth, reflective surface and a textured edge for grip during installation.

  6. Obnovit napájení:

    Once installation is complete and all connections are secure, restore power at the consumer unit/fuse box.

6. Návod k obsluze

The Luceco LED IP65 Fire Rated GU10 Downlight operates via your standard wall light switch. Simply toggle the switch to turn the light on or off.

7. Údržba

  • Čištění: Ensure power is off before cleaning. Wipe the polished chrome bezel with a soft, dry, or slightly damp tkanina. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.
  • Výměna žárovky:
    1. Vypněte hlavní napájení.
    2. Carefully twist the polished chrome bezel counter-clockwise to remove it from the main housing.
    3. Gently push the GU10 bulb upwards and twist counter-clockwise to remove it from the lamp držák.
    4. Insert a new GU10 bulb (max 35W, max length 50-60mm) by aligning the pins, pushing, and twisting clockwise.
    5. Reattach the bezel by aligning and twisting clockwise until secure.
    6. Obnovte napájení.

8. Řešení problémů

ProblémMožná příčinaŘešení
Světlo se nerozsvítí.
  • Obvod není napájen.
  • Vadná žárovka.
  • Uvolněné připojení kabeláže.
  • Zkontrolujte jistič/pojistku.
  • Replace GU10 bulb.
  • Switch off power and check wiring connections. Consult a qualified electrician if unsure.
Bezel does not sit flush.
  • Incorrectly aligned.
  • Obstrukce.
  • Remove and re-align the bezel, twisting clockwise until secure.
  • Check for any debris or misaligned components.

9. Informace o recyklaci

This product falls under the Waste Electrical and Electronic Equipment (WEEE) directive. Do not dispose of electrical products with household waste. Please recycle where facilities exist. Check with your local authority for recycling advice.

For information on recycling light bulbs and how to clean up broken lamps, please refer to local guidelines or official recycling resources.

10. Záruka a podpora

Luceco products are manufactured to high standards and are designed for durability. For specific warranty details or technical support, please refer to the warranty card included with your purchase or visit the official Luceco webUschovejte si doklad o koupi pro případ reklamace.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.