SoloGood 3DR 500MW 915Mhz Radio Telemetry Kit Instruction Manual

Zavedení

This manual provides comprehensive instructions for the SoloGood 3DR 500MW 915Mhz Radio Telemetry Kit. This kit is designed for reliable two-way half-duplex wireless communication, enabling data transmission between your flight controller (such as APM 2.6, APM 2.8, PX4, or Pixhawk) and a ground station. It features an open-source Xbee replacement radio set with enhanced range and performance, utilizing HopeRF's HM-TRP data link modules and custom SiK firmware.

Obsah balení

Ověřte, zda balení obsahuje všechny následující komponenty:

• 1 x Radio Telemetry Base Station (USB Connection)
• 1 x Telemetry Transceiver (Pin Header)
• 1 x Lead Set (connection cables)
• 2 x Anténa
• 1 x OTG Cable (for Android device connection)

Figure 1: Complete package contents of the telemetry kit.

Konec produktuview

The SoloGood 3DR 500MW 915Mhz Radio Telemetry Kit consists of two main modules: the Air Module and the Ground Module, along with two antennas and an OTG cable for mobile device connectivity.

Figure 2: Key components and connection points of the telemetry kit.

The Vzduchový modul connects to your flight controller and features a telemetry port and an SMA port for antenna connection. The Pozemní modul connects to your computer via a USB port or to an Android device using the provided OTG cable, also featuring an SMA port for its antenna.

Figure 3: Air and Ground Modules with antennas connected.

Pokyny pro nastavení

1. Připojení antén: Securely attach one antenna to the SMA port of the Air Module and the other antenna to the SMA port of the Ground Module. Ensure they are finger-tight.
2. Air Module Connection: Connect the Air Module to your flight controller (e.g., APM 2.6, APM 2.8, PX4, Pixhawk 2.4.7, Pixhawk 2.4.8) using the provided lead set. Refer to your flight controller's documentation for the correct telemetry port pinout.
3. Ground Module Connection:
   • Pro počítač: Plug the Ground Module directly into an available USB port on your computer.
   • Pro zařízení Android: Use the provided OTG cable to connect the Ground Module to your Android smartphone or tablet.
4. Instalace ovladače (pokud je to nutné): For computer connections, your operating system may automatically install necessary drivers. If not, you may need to manually install drivers for the USB serial port.
5. Konfigurace přenosové rychlosti: The telemetry kit is typically pre-configured to a baud rate of 57600. When setting up your ground station software (e.g., Mission Planner), ensure this baud rate is selected. Note: Some documentation or older kits might suggest 115200, but 57600 is the common default for this specific kit.
6. Výběr COM portu: In your ground station software, select the correct COM port corresponding to the connected Ground Module. Do not select "AUTO" as this can lead to connection issues.

Návod k obsluze

Once the hardware is connected and configured, you can begin operating your telemetry system.

1. Zapnutí: Ensure your flight controller and the connected Air Module are powered on. The Ground Module will receive power via its USB connection.
2. Launch Ground Station Software: Open your preferred ground station software (e.g., Mission Planner, QGroundControl) on your computer or Android device.
3. Navázat spojení:
   • Select the correct COM port for the Ground Module.
   • Set the baud rate to 57600.
   • Click the "Connect" button within the software.
4. Monitorovací data: Upon successful connection, you should see real-time flight data, GPS information, battery status, and other telemetry data displayed in your ground station software.
5. Upgrady firmwaru: The SiK firmware includes a bootloader, allowing for radio firmware upgrades over the serial interface. Consult the SiK firmware documentation for detailed upgrade procedures.

Údržba

To ensure the longevity and optimal performance of your telemetry kit, follow these maintenance guidelines:

• Zacházejte opatrně: Avoid dropping the modules or subjecting them to excessive force.
• Udržujte v suchu: Protect the modules from moisture and extreme temperatures.
• Čisté připojení: Periodically inspect and gently clean the SMA ports and pin headers to ensure good contact.
• Péče o anténu: Ensure antennas are not bent or damaged. A damaged antenna can significantly reduce range and performance.

Odstraňování problémů

If you encounter issues with your telemetry kit, refer to the following troubleshooting steps:

• Žádné připojení:
  • Verify that both modules are powered on.
  • Ujistěte se, že jsou antény bezpečně připevněny.
  • Check that the correct COM port is selected in your ground station software. Avoid "AUTO" selection.
  • Confirm the baud rate is set to 57600.
  • Zkontrolujte všechna kabelová spojení, zda nejsou uvolněná nebo poškozená.
  • Zkuste jiný port USB na počítači.
• Interference with GPS/Compass:
  • Some users have reported potential interference with GPS or compass modules, especially with 500mW devices.
  • Zkuste zvýšitasing the physical distance between the telemetry air module and your flight controller's GPS/compass unit.
  • Ensure proper shielding of components if possible.
• Incompatible Flight Controller:
  • While compatible with APM and Pixhawk series, this kit may not be compatible with all flight controllers (e.g., Holybro 6C has been reported as incompatible).
  • Verify pinout compatibility if using a non-standard flight controller.
• Incorrect Baud Rate:
  • The default baud rate is 57600. If you are unable to connect, double-check this setting in your ground station software. Some older documentation might incorrectly suggest 115200.

Specifikace

Figure 4: The telemetry kit components on a scale, showing approximate weight.

Podpora

For any technical questions or support regarding your SoloGood 3DR 500MW 915Mhz Radio Telemetry Kit, please contact our customer service. We are committed to providing the best service to assist you with any issues or inquiries.