Insignia Dual Arm Full Motion Monitor Mount User Manual

1. Konec produktuview

The Insignia Dual Arm Full Motion Monitor Mount is designed to securely hold two monitors, providing flexible positioning and an organized workspace. This mount supports most monitors ranging from 10 to 30 inches, offering a 360-degree rotation, and a tilt range of -85 to 15 degrees. Its robust aluminum construction ensures stability and durability.

Obrázek 1.1: Insignia Dual Arm Full Motion Monitor Mount in use, supporting two monitors on a desk.

2. Pokyny k nastavení

2.1. Obsah balení

Před zahájením instalace se ujistěte, že jsou přítomny všechny komponenty:

• Dual monitor arm assembly
• Psací stůl třamp báze
• VESA mounting plates (2)
• Hardware kit (screws, washers, Allen keys)

2.2. Pracovní stůl Clamp Instalace

1. Umístěte psací stůl třamp base onto the edge of your desk.
2. Utáhněte třamp screw until the mount is securely fastened to the desk. Ensure the clamp is stable and does not wobble. For thicker desks, you may need to adjust the mounting screw orientation as described in the troubleshooting section.
3. Insert the main pole of the monitor arm assembly into the clamp základnu a zajistěte ji dodaným šroubem.

Obrázek 2.1: Detail of the desk clamp mechanism securing the mount to a desk surface.

2.3. Monitor Attachment

1. Attach a VESA mounting plate to the back of each monitor using the appropriate screws from the hardware kit. Ensure the screws are tightened securely.
2. Carefully slide each monitor (with the attached VESA plate) onto the corresponding arm of the mount. Ensure the plate locks into place.
3. Tighten any security screws on the VESA plate to prevent accidental detachment.

Obrázek 2.2: VESA mounting plate attached to the rear of a monitor, connecting to the arm.

2.4. Správa kabelů

Route monitor cables through the integrated cable management channels on the arms and main pole to maintain a tidy workspace. Secure cables with ties if necessary.

3. Operating Your Monitor Mount

3.1. Nastavení polohy monitoru

The full-motion design allows for various adjustments:

• Nastavení výšky: Gently raise or lower the monitor arms to your desired height. The internal gas spring assists with this movement.
• Náklon: Tilt your monitor screen up or down (-85 to 15 degrees) to reduce glare and optimize viewing úhly.
• Otočný: Swivel the monitor left or right to share your screen or adjust your viewing pozice.
• Otáčení: Otočením monitoru o 360 stupňů přepínáte mezi orientací na šířku a na výšku.

3.2. Nastavení napětí plynové pružiny

If your monitor sags or does not stay in the desired height, the gas spring tension may need adjustment. Use the provided Allen key to turn the adjustment screw located on the arm joints. Turn clockwise to increase tension for heavier monitors, or counter-clockwise to decrease tension for lighter monitors. Adjust gradually until the monitor holds its position stably.

4. Údržba

• Čištění: Wipe the mount surfaces with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Pravidelné kontroly: Pravidelně kontrolujte všechny šrouby a spoje, zda jsou pevně utažené a bezpečné. V případě potřeby je dotáhněte.

5. Řešení problémů

• Monitor se prohýbá nebo nedrží svou polohu: Adjust the gas spring tension using the provided Allen key. Refer to Section 3.2 for detailed instructions.
• Hora se zdá být nestabilní: Zajistěte stůl třamp is fully tightened to the desk. Check that the main pole is securely fastened to the clamp báze.
• Mount Does Not Fit Thick Desk: If your desk is thicker than standard, you may need to reverse the mounting screw on the clamp to maximize its length. Consult the product's online resources or contact support for specific guidance.

6. Specifikace produktu

7. Záruka a podpora

Informace o záruce nebo technickou podporu naleznete v dokumentaci dodané s vaším nákupem nebo navštivte oficiální webové stránky Insignia. website. You may also contact Insignia customer service for assistance with product inquiries, troubleshooting, or replacement parts.