Uživatelská příručka k dobíjecí svítilně JETBeam SF-R26

Zavedení

The JETBeam SF-R26 is a high-performance, rechargeable LED flashlight designed for a wide range of lighting needs. Built with military-grade quality, it offers exceptional brightness and durability, making it suitable for various applications. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your SF-R26 flashlight.

Figure 1: JETBeam SF-R26 Rechargeable Flashlight, showcasinjeho kompaktní a robustní konstrukce.

Bezpečnostní informace

• Bezpečnost očí: Do not shine the flashlight directly into eyes. The powerful beam can cause temporary vision impairment or permanent eye damage.
• Teplo: The flashlight may become warm during prolonged use, especially on higher output modes. Handle with care.
• Bezpečnost baterie:
  • Use only recommended battery types (1x 18650 or 2x CR123A).
  • Nekombinujte staré a nové baterie ani různé typy baterií.
  • Při instalaci dbejte na správnou polaritu baterie.
  • Nevhazujte baterie do ohně. Mohou explodovat.
  • If the flashlight will not be used for an extended period, remove the batteries to prevent leakage.
• Voděodolnost: While the SF-R26 is resistant to strong water jets, it is not designed for prolonged submersion. Ensure the USB port cover is securely closed when exposed to water.
• Děti: Uchovávejte mimo dosah dětí.

Obsah balení

Po otevření balení se prosím ujistěte, že obsahuje všechny následující položky:

• JETBeam SF-R26 Flashlight
• Micro USB nabíjecí kabel
• 18650 Rechargeable Battery (if included with specific package)
• Šňůrka
• Náhradní O-kroužky
• Uživatelská příručka (tento dokument)

Figure 2: Contents typically included with the JETBeam SF-R26 flashlight, including the flashlight, battery, USB cable, and accessories.

Nastavení

1. Instalace baterie

The SF-R26 can be powered by one 18650 rechargeable Li-ion battery or two CR123A batteries. Ensure the battery is inserted with the positive (+) end facing towards the head of the flashlight.

1. Odšroubujte koncovku svítilny.
2. Insert the battery(ies) according to the polarity markings. For 18650, the positive end goes towards the head. For CR123A, both positive ends go towards the head.
3. Pevně ​​zašroubujte zadní krytku zpět, abyste zajistili správný kontakt a vodotěsnost.

2. Charging (for 18650 battery)

The SF-R26 features a convenient micro USB charging port for internal recharging of an 18650 battery. CR123A batteries are NOT rechargeable via the flashlight's USB port.

1. Locate the micro USB charging port on the side of the flashlight. It is usually covered by a rubber flap.
2. Gently lift the rubber flap to expose the port.
3. Connect the micro USB cable to the flashlight's port and the other end to a USB power source (e.g., computer, wall adapter).
4. The side switch LED indicator will show charging status (e.g., red for charging, green for fully charged).
5. Once charging is complete, disconnect the cable and firmly press the rubber flap back into place to maintain water resistance.

Figure 3: The micro USB charging port on the side of the SF-R26, shown with a charging cable connected.

Návod k obsluze

1. Zapnutí/vypnutí (zadní spínač)

The tactical tail cap switch controls the main power of the flashlight.

• Okamžitě zapnuto: Half-press the tail switch to momentarily turn on the light. Release to turn off.
• Neustálé zapnutí/vypnutí: Fully press the tail switch until it clicks to turn the light on or off.

Figure 4: The tactical tail switch of the SF-R26, used for power control.

2. Výběr režimu (boční spínač)

With the flashlight turned on, use the side switch to cycle through different brightness levels and special modes.

• Úrovně jasu: Short press the side switch to cycle through the available brightness modes (e.g., Low, Medium, High, Turbo). The SF-R26 offers 3 dimming outputs (10 lumens, 250 lumens) and a maximum output of 1200 lumens.
• Stroboskopický režim: Press and hold the side switch for approximately 1-2 seconds to activate the Strobe mode. Short press again to return to the previous brightness level.

Figure 5: The side switch of the SF-R26, used for cycling through brightness modes and activating strobe.

3. Indikátor napájení

The side switch also functions as an LED power indicator. It will flash slowly and then quickly to indicate when the battery charge is low and needs replacement or recharging.

Údržba

• Čištění: Očistěte tělo svítilny měkkým hadříkemamp tkanina. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.
• Závity a O-kroužky: Závity a O-kroužky pravidelně promazávejte silikonovým mazivem, aby byla zajištěna jejich vodotěsnost a plynulý chod. Pokud se O-kroužky zdají být poškozené nebo opotřebované, vyměňte je.
• Péče o baterie:
  • Baterie skladujte na chladném a suchém místě.
  • If using rechargeable 18650 batteries, recharge them regularly, even if not fully depleted, to prolong battery life.
  • Pokud svítilnu nebudete delší dobu používat, vyjměte baterie, abyste zabránili jejímu vytečení a poškození.

Odstraňování problémů

Specifikace

Obrázek 6: Detail view of the CREE XP-L HI LED emitter, highlighting the light source.

Záruka a podpora

JETBeam products are manufactured to high quality standards. For specific warranty details, please refer to the warranty card included with your product or visit the official JETBeam website. If you encounter any issues or require technical assistance, please contact JETBeam customer support or your authorized dealer.

Výrobce: Sportsman Supply Inc.

Datum první dostupnosti: 24. února 2017