Uživatelská příručka k digitálnímu momentovému klíči M-Wave 3–60 Nm s alarmem

Zavedení

This manual provides comprehensive instructions for the safe and effective use of your M-Wave 3-60 Nm Digital Torque Wrench with Alarm. Please read this manual thoroughly before operation and retain it for future reference.

The M-Wave Digital Torque Wrench is designed for precise torque application, ensuring fasteners are tightened to their specified values within a range of 3 to 60 Newton meters (Nm) with a tolerance of +/- 2%. It features a reversible ratchet head and an audible alarm to indicate when the desired torque is reached.

Obsah balení

Ověřte, zda jsou v balení přítomny všechny položky:

• M-Wave Digital Torque Wrench (3/8" head)
• Pevné úložné pouzdro
• Hex bits: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm
• Sockets (nuts): 8mm, 9mm, 10mm, 11mm, 12mm, 13mm, 14mm, 15mm
• Torx bits: T25, T30, T40
• Philips screwdriver head

Image: The M-Wave Digital Torque Wrench and its complete accessory set, neatly organized within its hard storage case. This image displays the wrench, various hex bits, sockets, and Torx bits.

Nastavení

1. Instalace baterie

The digital torque wrench requires batteries for operation. Locate the battery compartment, typically at the base of the handle. Insert the required batteries, ensuring correct polarity. Close the compartment securely.

2. Attaching Bits/Sockets

Select the appropriate hex bit, socket, or Torx bit for your application. Insert the chosen accessory firmly into the 3/8" square drive head of the torque wrench. Ensure it is securely seated to prevent slippage during use.

Obrázek: Detailní záběr view of the various sockets included with the M-Wave Digital Torque Wrench, ranging in size from 8mm to 15mm. These are designed for use with the 3/8" drive head.

Obrázek: Podrobný view of the hex and Torx bits provided with the M-Wave Digital Torque Wrench. This includes hex sizes 3mm to 10mm and Torx sizes T25, T30, T40, along with a Philips head bit.

Návod k obsluze

1. Zapnutí/vypnutí

Press and hold the power button (usually marked 'C' or 'ON/OFF') to turn the wrench on. The digital display will illuminate. To power off, press and hold the same button until the display turns off.

2. Setting Torque Value

Use the 'U/S' button to cycle through units (Nm, ft-lb, in-lb, kg-cm). Use the 'A' (up) and 'V' (down) buttons to adjust the desired torque value. The display will show the set torque. Ensure the desired torque is within the 3-60 Nm operating range.

Obrázek: Podrobný view of the M-Wave Digital Torque Wrench's control panel, showing the digital display and the 'U/S', 'A', and 'V' buttons used for setting torque values and units.

3. Použití krouticího momentu

1. Attach the appropriate bit or socket to the wrench head.
2. Place the wrench onto the fastener.
3. Apply steady, smooth force to the wrench handle.
4. As you approach the set torque value, the wrench will emit an audible alarm and the display may flash.
5. Stop applying force immediately when the alarm sounds continuously or the display indicates the target torque has been reached.

Důležité: Do not overtighten. The alarm indicates the precise moment the target torque is achieved. Continuing to apply force beyond this point can damage the fastener or the component.

4. Reversible Ratchet Function

The wrench features a reversible ratchet head. A small lever or switch on the head allows you to change the direction of rotation for tightening or loosening fasteners. Ensure the ratchet direction is set correctly before applying torque.

Údržba

• Čištění: Wipe the wrench clean with a soft, dry cloth after each use. Do not use abrasive cleaners or solvents.
• Skladování: Store the torque wrench and its accessories in the provided hard case when not in use. Keep it in a dry environment, away from extreme temperatures and direct sunlight.
• Výměna baterie: If the display becomes dim or the wrench fails to power on, replace the batteries. Dispose of old batteries responsibly.
• Kalibrace: Digital torque wrenches require periodic calibration to maintain accuracy. Refer to the manufacturer's recommendations for calibration intervals.

Odstraňování problémů

Specifikace

• Model: 880266
• Rozsah točivého momentu: 3-60 Nm
• Přesnost: +/- 2 %
• Velikost disku: 3/8 palce
• Provozní režim: Electric (Digital)
• Zahrnuté komponenty: Ratchet, 18 bits, hard case
• Materiál: Silver (components), Black (handle/case)
• Hmotnost položky: Přibližně 16 unce (0.45 kg)
• Dimensions (Wrench): Přibližně 11.81 x 4.72 x 2.76 palce
• UPC: 887539017279

Záruka a podpora

For warranty information or technical support, please refer to the documentation included with your purchase or visit the official M-Wave webUschovejte si doklad o koupi pro případ reklamace.

Výrobce: Cycle Force Group

Kontakt: Další pomoc naleznete na adrese www.m-wave.com nebo kontaktujte svého prodejce.