Návod k obsluze napájecího zdroje Keithley 2303-PJ

1. Konec produktuview

The Keithley 2303-PJ is a specialized power supply designed for testing portable, battery-operated devices. It offers advanced capabilities to simulate a battery's performance across a wide range of conditions, including output resistance and voltage response. This instrument is crucial for accurately testing device charge control circuitry and overall battery simulation.

Mezi klíčové vlastnosti patří:

• Ultra-fast response to transient load currents
• Variable output resistance
• 100nA DC current sensitivity

Figure 1: Front panel of the Keithley 2303-PJ Power Supply. The display shows voltage and current readings (e.g., 3.60V, 1.08A). Controls include a navigation pad, 'DISPLAY', 'MENU', 'OPERATE', 'ENTER', 'SET' buttons, and a 'POWER' button with indicator lights.

2. Nastavení

1. Vybalení a kontrola: Carefully remove the instrument from its packaging. Inspect for any signs of damage during transit. Report any damage to the shipping carrier and Keithley immediately.
2. Připojení napájení: Connect the supplied AC power cord to the instrument's rear panel power inlet and then to a grounded AC power outlet. Ensure the power source matches the instrument's voltage požadavky.
3. Počáteční zapnutí: Stiskněte tlačítko MOC button located on the front panel. The display should illuminate, indicating the unit is operational.
4. Connecting to Device Under Test (DUT): Use appropriate test leads to connect the output terminals of the 2303-PJ to the device you intend to test. Observe correct polarity.
5. Větrání: Ensure adequate ventilation around the instrument. Do not block the ventilation grilles on the sides or rear of the unit.

3. Návod k obsluze

3.1 Ovládací prvky na předním panelu

• Zobrazit: Zobrazuje výstupní objemtage, proud a další provozní parametry.
• Navigační tlačítka (nahoru, dolů, vlevo, vpravo): Používá se k navigaci v menu a úpravě hodnot parametrů.
• Tlačítko ENTER: Confirms selections or entered values.
• Tlačítko SET: Vstupuje do režimu nastavení parametrů.
• Tlačítko MENU: Accesses the main menu for configuration and advanced settings.
• OPERATE Button: Toggles the output on or off.
• Tlačítko DISPLAY: Cycles through different display modes or views.

3.2 Základní obsluha

1. Nastavení Voltage a aktuální:
   • Stiskněte tlačítko SOUBOR tlačítko.
   • Use the navigation buttons to select the voltage or current parameter you wish to adjust.
   • Use the navigation buttons (typically Up/Down) to change the value.
   • Stiskněte ENTER pro potvrzení nastavení.
2. Povolení výstupu:
   • Once parameters are set, press the PROVOZUJTE button to enable the power output. The output indicator should illuminate.
   • To disable the output, press PROVOZUJTE znovu.
3. Monitorovací údaje:

   The display continuously shows the actual output voltage and current. Use the ZOBRAZIT button to cycle through different measurement viewpokud jsou k dispozici.

4. Údržba

• Čištění: Keep the instrument clean by wiping the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and disconnected from the AC supply before cleaning.
• Větrání: Periodically check that the ventilation grilles are free from dust and debris to ensure proper airflow and prevent overheating.
• Skladování: When not in use for extended periods, store the instrument in a clean, dry environment within its specified operating temperature and humidity ranges.
• Kalibrace: For optimal performance and accuracy, periodic calibration by qualified personnel is recommended. Refer to the Keithley service manual or contact Keithley support for calibration procedures and intervals.

5. Řešení problémů

For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Keithley technical support.

6. Specifikace

7. Záruka a podpora

Warranty information for the Keithley 2303-PJ Power Supply is typically provided with the product at the time of purchase or can be found on the official Keithley webstránky. Uschovejte si prosím doklad o koupi pro případ reklamace.

For technical support, service, or calibration inquiries, please contact Keithley customer service directly. Refer to the contact information provided in your product documentation or on the official Keithley webweb (www.tek.com/keithley).