Zavedení
This manual provides detailed instructions for the proper use, setup, operation, and maintenance of your INSIZE 2167-25 Electronic Snap Gage. Please read this manual thoroughly before operating the device to ensure accurate measurements and prolong its lifespan.
Konec produktuview
The INSIZE 2167-25 is an electronic snap gage designed for precise external dimensional measurements. It features a digital display for clear readings and a spring-loaded mechanism for consistent contact pressure.
Figure 1: The INSIZE 2167-25 Electronic Snap Gage. This image displays the full device, highlighting its C-shaped frame, the measuring anvils, the digital display, and control buttons for power, unit conversion, and zero setting.
Klíčové vlastnosti
- Rozsah měření: 0-1 palců / 0-25 mm
- Rezoluce: 0.0005 palce / 0.01 mm
- Přesnost: +/- 0.0005 inch / +/- 0.012mm
- Mechanismus: Spring snap for consistent measuring force.
- Digitální displej: Clear electronic readout for easy interpretation.
- Převod jednotek: Switch between inches and millimeters.
- Nastavení nuly: Ability to set zero at any point.
Nastavení
- Rozbalení: Carefully remove the snap gage from its packaging. Inspect for any visible damage.
- Instalace baterie: The device typically comes with a battery installed or requires one. If not installed, locate the battery compartment (usually on the back or side of the display unit), open it, and insert the correct battery type (e.g., CR2032) with the correct polarity.
- Čištění: Before first use, gently wipe the measuring anvils with a clean, lint-free cloth. Ensure no dust or debris is present on the measuring surfaces.
- Podmínky prostředí: Operate the snap gage in a stable environment, avoiding extreme temperatures, humidity, or direct sunlight, which can affect accuracy.
Návod k obsluze
- Zapnutí: Stiskněte tlačítko ON button to turn on the device. The display will illuminate and show a reading.
- Výběr jednotky: Stiskněte tlačítko in/mm button to switch between inch and millimeter units as required. The selected unit will be indicated on the display.
- Nastavení nuly:
- Ensure the measuring anvils are clean and free of debris.
- Gently close the anvils until they make contact.
- Stiskněte tlačítko NULA button. The display should now read 0.000 (or 0.00 in mm). If it does not, repeat the process.
- Provedení měření:
- Open the measuring anvils wider than the object to be measured.
- Position the object between the anvils.
- Release the anvils gently so they make firm contact with the object. The spring mechanism ensures consistent measuring force.
- Odečtěte naměřenou hodnotu přímo z digitálního displeje.
- Vypnout: Stiskněte tlačítko VYPNUTO button to turn off the device when not in use to conserve battery life. The device may also have an auto-off feature.
Údržba
- Čištění: Regularly clean the measuring surfaces and the body of the snap gage with a soft, lint-free cloth. For stubborn dirt, a small amount of isopropyl alcohol can be used, applied to the cloth, not directly to the device.
- Skladování: Store the snap gage in its protective case (if provided) in a dry, clean environment away from direct sunlight, extreme temperatures, and corrosive substances.
- Výměna baterie: When the display becomes dim or erratic, replace the battery promptly. Refer to the "Setup" section for battery installation instructions.
- Kalibrace: U kritických aplikací se doporučuje pravidelná kalibrace kvalifikovaným technikem, aby byla zajištěna trvalá přesnost.
Odstraňování problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Displej je prázdný nebo tmavý. | Slabá nebo vybitá baterie; nesprávná instalace baterie. | Replace the battery; ensure correct polarity. |
| Nepřesné údaje. | Dirty measuring surfaces; improper zero setting; environmental factors. | Clean anvils thoroughly; re-zero the device; ensure stable operating conditions. |
| Tlačítka nereagují. | Low battery; internal malfunction. | Vyměňte baterii. Pokud problém přetrvává, kontaktujte zákaznickou podporu. |
Specifikace
- Číslo modelu: 2167-25
- Značka: VE VELIKOSTI
- Rozsah měření: 0-1 palců / 0-25 mm
- Rezoluce: 0.0005 palce / 0.01 mm
- Přesnost: +/- 0.0005 inch / +/- 0.012mm
- Rozměry položky: Refer to package dimensions for shipping (7.68 L x 1.69 H x 4.61 W inches).
- První dostupné datum: 4. června 2016
Záruka a podpora
Information regarding specific warranty terms for the INSIZE 2167-25 Electronic Snap Gage is not provided in this document. For warranty details, technical support, or service inquiries, please refer to the official INSIZE website or contact your authorized INSIZE dealer. Keep your purchase receipt as proof of purchase.