BTF-LIGHTING 16.4ft Warm White SMD5630 LED Strip Light User Manual

Zavedení

This manual provides essential information for the safe and effective installation, operation, and maintenance of your BTF-LIGHTING 16.4ft Warm White SMD5630 LED Strip Light. Please read this manual thoroughly before use and retain it for future reference.

Bezpečnostní informace

Před instalací nebo údržbou se ujistěte, že je odpojeno napájení.
This LED strip is designed for 12V DC power only. Connecting to a higher voltage poškodí produkt.
This product is IP30 rated, meaning it is non-waterproof. Avoid exposure to water or high humidity.
Do not bend the LED strip sharply or apply excessive force, as this may damage the circuit board or LEDs.
Ensure proper ventilation around the LED strip to prevent overheating.
Uchovávejte mimo dosah dětí.
Only use the recommended power adapter (DC12V3A) or a compatible power supply.

Obsah balení

Ověřte, zda jsou všechny komponenty přítomny a v dobrém stavu:

1 x BTF-LIGHTING 16.4ft (5m) Warm White SMD5630 LED Strip Light
1 x Remote Control (if included with your specific package)
Note: Power adapter is typically sold separately.

Specifikace

Značka	BTF-OSVĚTLENÍ
Číslo modelu	56305MWW60W30
Typ LED	SMD5630
Množství LED	300 LED diod (60 LED diod/metr)
Délka pásku	16.4 stop (5 metrů)
FPCB Board Width	10 mm
Světlá barva	Teplá bílá
Teplota barev	2700K-3000K
Lumen per LED	23-25 lm/LED
Pracovní svtage	DC 12V
Doporučený napájecí adaptér	DC 12V 3A (36W) or higher
Wattage	30 wattů
Vodotěsná úroveň	IP30 (Non-Waterproof)
Provozní teplota	-20 °C až 50 °C
Životnost	> 50,000 hodin
Certifikace	CE a RoHS

Pokyny pro nastavení

Připravte povrch: Ensure the installation surface is clean, dry, and smooth. Dust, oil, or moisture can reduce the adhesive's effectiveness.
Obrázek: Detail view of the LED strip, highlighting individual SMD5630 LEDs and designated cut points marked with a scissor icon. The strip also shows the adhesive backing being peeled.
Změření a řezání (volitelné): If a shorter length is required, cut the LED strip only at the designated cut marks (usually indicated by a scissor icon and copper pads). Cutting elsewhere will damage the circuit and prevent the section from lighting up.
Připojte napájení:
- Identify the 2-pin connectors on the LED strip.
- Connect the LED strip's 2-pin connector to a compatible DC 12V power adapter (not included). Ensure polarity is correct (positive to positive, negative to negative).
- If a remote control is included, connect the LED strip to the remote controller, and then connect the controller to the power adapter.
Image: Two separate sections of the LED strip, each terminating with a 2-pin connector (red and black wires), ready for connection to a power source or controller.
Test Before Adhering: Before removing the adhesive backing, plug in the power adapter to test if the LED strip lights up correctly. This allows for troubleshooting before permanent installation.
Přilepte proužek: Once tested, peel off the protective backing from the adhesive tape on the back of the LED strip. Carefully press the strip onto the desired clean, dry surface. Apply firm, even pressure along the entire length to ensure good adhesion.

Návod k obsluze

Once the LED strip is properly installed and connected to a 12V DC power supply:

Zapnutí/vypnutí: Plug the power adapter into a wall outlet to turn the strip light on. Unplug it to turn it off.
Using the Remote Control (if applicable): If your package included a remote control, refer to its specific instructions for functions such as brightness adjustment or on/off control.

Examples of warm white LED strip lighting in various indoor settings

Obrázek: Vizuální examples of LED strip lighting used in different indoor environments, demonstrating the warm white illumination. This image also shows Cool White and Nature White, but this product is Warm White.

Údržba

Čištění: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
Inspekce: Periodically check the strip for any signs of damage, loose connections, or adhesive degradation.
Skladování: If storing the LED strip, ensure it is kept in a dry, cool place, away from direct sunlight and extreme temperatures.

Odstraňování problémů

Problém	Možná příčina	Řešení
LED pásek nesvítí.	Adaptér není napájen. Incorrect power connection (polarity reversed). Vadný napájecí adaptér. Poškozený LED pásek. Remote control battery dead or not paired (if applicable).	Check wall outlet and power adapter connection. Ensure positive (+) and negative (-) connections are correct. Test with a known working 12V DC power adapter. Inspect the strip for visible damage, especially at cut points. Replace remote battery or re-pair according to remote instructions.
Část LED pásku nesvítí.	Poškození části pásu. Nesprávné řezání.	Inspect the unlit section for physical damage or a broken circuit. Ensure cuts were made only at designated marks. Damaged sections cannot be repaired.
LED diody svítí tlumeně nebo blikají.	Nedostatečné napájení. Uvolněné spojení.	Ensure the power adapter provides sufficient wattage (minimum 30W for this strip). Check all connections for secure fit.

Záruka a podpora

BTF-LIGHTING products are designed for reliability and performance. For warranty information, technical support, or assistance with your product, please contact BTF-LIGHTING customer service through the retailer where the product was purchased or visit the official BTF-LIGHTING webmísto.

Please have your model number (56305MWW60W30) and purchase details ready when contacting support.

BTF-LIGHTING 56305MWW60W30