1. Konec produktuview
The Eberle KLR-E 7010 is a bimetal thermostat designed for controlling fancoil units. It provides precise temperature regulation and offers control over fan speed and operating mode (heating or cooling). This manual provides essential information for the safe and efficient installation, operation, and maintenance of your thermostat.
Obrázek 1: Přední view of the Eberle KLR-E 7010 Fancoil Thermostat. The image displays the front panel of the thermostat, which is white with the 'EBERLE' brand name in the top left. On the right side, there is a large rotary dial for temperature setting, marked in degrees Celsius from 5 to 30. An arrow indicates the current setpoint. On the left, there are two horizontal slide switches. The top switch controls the fan speed, with icons representing different fan speeds. The bottom switch selects between heating (wavy lines), off (center), and cooling (snowflake) modes.
2. Důležité bezpečnostní pokyny
- Always disconnect power to the fancoil unit and thermostat at the main circuit breaker before performing any installation, wiring, or maintenance.
- Instalaci a zapojení musí provést kvalifikovaný elektrikář v souladu se všemi místními a národními elektrotechnickými předpisy.
- Do not operate the thermostat with wet hands or when standing on a wet surface.
- Ujistěte se, že všechna kabelová spojení jsou bezpečná a řádně izolovaná, abyste předešli nebezpečí úrazu elektrickým proudem.
- This device is designed for indoor use only. Do not expose it to moisture, extreme temperatures, or direct sunlight.
- Keep the thermostat away from children and pets.
3. Instalační příručka
3.1. Obsah balení
Před zahájením instalace ověřte, zda jsou všechny komponenty přítomny:
- Eberle KLR-E 7010 Fancoil Thermostat unit
- Mounting screws (typically included with the unit)
- Návod k použití (tento dokument)
3.2. Montážní pokyny
- Vyberte umístění: Choose an interior wall location, approximately 1.5 meters (5 feet) above the floor, away from direct sunlight, drafts, heat sources, or areas with poor air circulation.
- Odpojit napájení: Turn off the power to the fancoil unit at the main circuit breaker. Verify that power is off using a voltage tester.
- Separate Base Plate: Opatrně oddělte přední kryt termostatu od jeho základní desky.
- Základní deska montáže: Position the base plate on the wall and mark the drilling locations. Drill holes and insert wall anchors if necessary. Secure the base plate to the wall using the provided mounting screws.
- Zapojení: Refer to the wiring diagram (Section 3.3) and connect the electrical wires to the appropriate terminals on the base plate. Ensure all connections are tight and correct.
- Připevněte přední kryt: Once wiring is complete and verified, carefully reattach the front cover to the base plate, ensuring it clicks securely into place.
- Obnovit napájení: Znovu zapněte napájení na hlavním jističi.
3.3. Schéma zapojení
The Eberle KLR-E 7010 thermostat is designed for 230 Volts systems. Due to variations in fancoil unit configurations and local electrical codes, a generic wiring diagram cannot be provided here. It is imperative that a qualified electrician performs all wiring to ensure proper functionality and safety. The electrician should consult the specific wiring instructions provided with your fancoil unit and the terminal markings on the thermostat's base plate.
4. Návod k obsluze
4.1. Ovládací prvky Overview
The thermostat features three primary controls:
- Číselník teploty: A large rotary dial on the right side of the unit, marked in degrees Celsius, used to set the desired room temperature.
- Přepínač otáček ventilátoru: A horizontal slide switch on the upper left, typically with three fan blade icons, allowing selection of low, medium, or high fan speed.
- Přepínač volby režimu: A horizontal slide switch on the lower left, used to select between heating (wavy lines), cooling (snowflake), or off (center) modes.
4.2. Nastavení teploty
To set the desired room temperature, rotate the large dial clockwise or counter-clockwise until the indicator arrow points to your preferred temperature in degrees Celsius. The thermostat will then work to maintain this temperature.
4.3. Ovládání rychlosti ventilátoru
Use the upper left slide switch to adjust the fancoil's fan speed:
- Nízký: For quiet operation and minimal air circulation.
- Střední: A balanced setting for general comfort.
- Vysoký: For rapid temperature change or maximum air circulation.
4.4. Mode Selection (Heating/Cooling)
Use the lower left slide switch to select the operating mode:
- Heating (wavy lines): The thermostat will activate the heating function when the room temperature falls below the setpoint.
- Vypnuto (uprostřed): The fancoil unit will remain off, regardless of temperature.
- Cooling (snowflake): The thermostat will activate the cooling function when the room temperature rises above the setpoint.
5. Údržba
The Eberle KLR-E 7010 thermostat requires minimal maintenance.
- Čištění: Periodically wipe the exterior of the thermostat with a soft, dry cloth to remove dust. Do not use abrasive cleaners, solvents, or spray directly onto the unit.
- Žádné díly opravitelné uživatelem: The thermostat contains no user-serviceable parts. Do not attempt to open or repair the unit yourself. Refer all servicing to qualified personnel.
6. Řešení problémů
If you experience issues with your Eberle KLR-E 7010 thermostat, consult the table below for common problems and potential solutions.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Thermostat not responding / No power | No power at the circuit breaker; Loose wiring connection. | Check the circuit breaker and ensure it is in the 'ON' position. Verify all wiring connections are secure (consult a qualified electrician). |
| Fancoil not heating/cooling | Incorrect mode selected; Temperature setpoint too high/low; Fancoil unit malfunction. | Ensure the mode switch is set to 'Heating' or 'Cooling' as desired. Adjust the temperature setpoint appropriately. Check the fancoil unit for operational issues. |
| Ventilátor nefunguje | Fan speed switch set to 'Off' (if applicable); Fancoil unit fan malfunction. | Ensure the fan speed switch is set to a desired speed (Low, Medium, or High). Check the fancoil unit's fan for issues. |
| Nepřesný údaj o teplotě | Thermostat located near heat/cold source or draft. | Relocate the thermostat to a more suitable position if possible, away from direct influences. |
If the problem persists after attempting these solutions, contact a qualified technician or customer support.
7. Technické specifikace
- Značka: Eberle
- Model: KLR-E 7010
- Typ: Bimetal Fancoil Thermostat
- svtage: 230 voltů
- Rozměry (D x Š x V): 11.71 x 7.11 x 2.69 cm (přibližně 4.61 x 2.80 x 1.06 palce)
- Hmotnost: 120 gramů (přibližně 0.26 libry)
- Ovládání ventilátoru: 3-speed fan selector
- Ovládání režimu: Heating/Cooling/Off selector
- Rozsah teplot: Typicky 5 °C až 30 °C (41 °F až 86 °F)
- Baterie: Not required, not included
- Reference výrobce: 3024146
- Article Model Number: 8402414979620
8. Informace o záruce
This Eberle KLR-E 7010 thermostat is covered by the manufacturer's standard warranty. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the documentation provided at the time of purchase or contact your retailer.
9. Zákaznická podpora
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the retailer from whom you purchased the product or visit the official Eberle website for support contact information. When contacting support, please have your product model (KLR-E 7010) and proof of purchase readily available.