UHPPOTE Proximity RFID Card Reader (Model UT0111-101A) Instruction Manual

1. Úvod

This manual provides detailed instructions for the installation, wiring, operation, and maintenance of the UHPPOTE Proximity RFID Card Reader, Model UT0111-101A. This device is designed for use in access control systems and requires connection to a compatible Wiegand protocol access controller.

Please read this manual thoroughly before installation and operation to ensure correct usage and optimal performance.

2. Konec produktuview a funkce

The UHPPOTE Proximity RFID Card Reader is a robust device designed for secure access control. It integrates seamlessly with Wiegand protocol access controllers to manage entry and exit points.

Obrázek 2.1: Přední strana view of the RFID Card Reader, showing its sleek black design and card icon.

Klíčové vlastnosti:

• Wiegand Protocol Compatibility: Supports Wiegand 26-bit or Wiegand 34-bit output formats, ensuring broad compatibility with various access control panels, fingerprint devices, or master controllers.
• Nízká spotřeba energie: Designed for efficiency with an ultra-low standby current of less than 50mA.
• Stabilní výkon: Utilizes a high-performance MCU (Microcontroller Unit) for reliable and consistent operation.
• Odolný design: Features an IP66 waterproof rating, providing good performance in various environmental conditions, including low temperatures.
• Všestranná aplikace: Suitable for a wide range of environments such as factories, residential quarters, offices, and mechanical/electrical control equipment.
• Important Note on Card Compatibility: This Wiegand reader is not compatible with certain encrypted cards, including but not limited to HID, Indala, Cobra, APCiK, Paradox, Radio, and Honeywell.

Figure 2.2: The RFID reader is rated IP66 waterproof, indicating its suitability for outdoor and harsh environments, and good performance in low temperatures.

3. Specifikace

Figure 3.1: Dimensions of the UHPPOTE Proximity RFID Card Reader.

4. Bezpečnostní informace

• Ensure all power is disconnected before performing any installation or wiring.
• Toto zařízení je určeno pro nízkou hlasitosttage DC operation. Do not connect to AC power directly.
• Installation should be performed by qualified personnel to prevent electrical hazards and ensure proper functionality.
• Avoid exposing the device to extreme physical shock or corrosive substances.
• Verify all wiring connections are secure and correct before applying power. Incorrect wiring can damage the device or connected equipment.

5. Nastavení a instalace

The RFID card reader is typically mounted near an entry point, such as a door frame. Ensure the mounting surface is stable and allows for proper cable routing.

Montážní kroky:

1. Choose a suitable location for the reader, typically at eye level next to the door.
2. Use the provided mounting template (if available) or the back plate of the reader to mark the drilling points on the wall or door frame.
3. Vyvrtejte vodicí otvory pro montážní šrouby.
4. Route the wiring from the access controller to the reader's mounting location.
5. Secure the reader's back plate to the wall using screws.
6. Connect the wiring as detailed in the "Wiring Diagram" section.
7. Attach the reader unit to its back plate, ensuring it is securely fastened.

Obrázek 5.1: Přample installation of the RFID reader on a door frame.

Figure 5.2: Mounting diagram for the RFID reader.

6. Schéma zapojení

The UHPPOTE Proximity RFID Card Reader must be connected to an access control panel or master controller via Wiegand protocol. Below are the general wiring connections. Always refer to your access controller's manual for specific wiring requirements.

Obrázek 6.1: Zpět view of the RFID reader with wiring harness.

Figure 6.2: Wiring labels on the back cover of the reader. Connections are: Red (+12V), Black (GND), White (D1), Green (D0), Blue (LED), Yellow (BEEP), Gray (WG34).

Obecné zapojení:

• Červený drát: +12V DC Power Input
• Černý drát: Země (GND)
• Bílý drát: Wiegand Data 1 (D1)
• Zelený drát: Wiegand Data 0 (D0)
• Modrý drát: LED Control (Connect to LED input on controller)
• Žlutý drát: BEEP Control (Connect to BEEP input on controller)
• Gray Wire: Wiegand 34-bit selection (Connect to GND for Wiegand 34-bit, leave open for Wiegand 26-bit)

Figure 6.3: Typical access control system setup with PC, access controller, and RFID reader.

Video: Wiring of Wiegand Access Control System

7. Návod k obsluze

Once properly installed and wired to an access control system, the UHPPOTE RFID Card Reader operates by reading compatible proximity cards or key fobs.

Základní provoz:

1. Zapnutí: Ensure the access control system and reader are powered on. The reader's LED indicator may show a standby status (e.g., red or green, depending on system configuration).
2. Dárková karta: Hold a compatible 125KHz RFID card or key fob within close proximity (typically 2-10 cm) of the reader.
3. Přístup povolen/zamítnut:
   • If the card is recognized and authorized by the access controller, the reader will typically emit a short beep and the LED indicator may change color (e.g., from red to green) to signal access granted. The connected lock will then unlock.
   • If the card is not recognized or unauthorized, the reader may emit a different sound or the LED may remain in its standby state, indicating access denied.
4. Výstup: For exiting, an exit button (if installed) or another reader on the inside will be used to unlock the door.

Figure 7.1: Demonstrating how to present an RFID key fob to the reader for access.

8. Údržba

The UHPPOTE RFID Card Reader is designed for minimal maintenance. Regular cleaning and inspection can help ensure its longevity and reliable operation.

• Čištění: Wipe the reader's surface with a soft, damp cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, which can damage the device.
• Inspekce: Periodically check the wiring connections for any signs of wear, corrosion, or loose contacts. Ensure the reader is securely mounted.
• Ochrana životního prostředí: Although IP66 rated, prolonged exposure to direct sunlight or extreme weather conditions may affect the lifespan of the device.

Figure 8.1: The reader's IP66 rating ensures protection against water splashes, but proper care is still recommended.

9. Řešení problémů

If you encounter issues with your RFID card reader, refer to the following troubleshooting steps:

If problems persist after following these steps, contact UHPPOTE customer support or a qualified technician.

10. Záruka a podpora

UHPPOTE products are manufactured to high quality standards. For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official UHPPOTE webmísto.

Kontaktní údaje:

• Značka: Uhppote
• Webmísto: Navštivte obchod UHPPOTE na Amazonu (obecné informace o produktu)
• For direct technical support, please refer to the contact details provided in your product packaging or on the manufacturer's official webmísto.