1. Úvod
This manual provides essential information for the safe installation, operation, and maintenance of your Everbilt SCN250-LQ 1/3 HP Pedestal Sump Pump. This pump is designed for residential applications to efficiently remove unwanted water from sump pits. Please read these instructions thoroughly before installation and operation to ensure proper function and safety.
2. Bezpečnostní informace
Always observe the following safety precautions to reduce the risk of injury, electric shock, or property damage:
- Odpojit napájení: Always disconnect the pump from the power source before performing any maintenance or service.
- Elektrické uzemnění: Ensure the pump is properly grounded. Do not remove the grounding prong from the power cord.
- Napájecí kabel: Do not operate the pump with a damaged power cord. Do not use extension cords.
- Teplota vody: Do not pump liquids hotter than 95°F (35°C) or colder than 35°F (1.7°C).
- Hořlavé kapaliny: Do not pump flammable or corrosive liquids. This pump is for water only.
- Pohyblivé části: Keep hands and foreign objects clear of the pump's inlet and discharge openings during operation.
3. Nastavení a instalace
The Everbilt SCN250-LQ pedestal sump pump is designed for easy installation and to fit into a 12-inch diameter or larger sump basin.
3.1 Vybalení
Carefully remove the pump and all components from the packaging. Inspect for any damage that may have occurred during shipping. If damage is found, do not proceed with installation and contact customer support.
Obrázek 1: Přesview of the Everbilt SCN250-LQ 1/3 HP Pedestal Sump Pump. This image shows the complete pump assembly, including the motor housing, pedestal shaft, and discharge outlet.
3.2 Sump Pit Preparation
Ensure your sump pit is clean and free of debris. The pit must be at least 12 inches in diameter to accommodate the pump properly.
3.3 Umístění čerpadla
Place the pump on a solid, level surface at the bottom of the sump pit. Ensure the pump is stable and will not tip over during operation.
Figure 2: The Everbilt SCN250-LQ pump showing the adjustable float and rod type switch. This component is crucial for automatic operation.
3.4 Připojení výtlačného potrubí
Connect a 1-1/4 inch NPT discharge pipe to the pump's outlet. It is recommended to install a check valve in the discharge line to prevent water from flowing back into the sump pit when the pump turns off.
3.5 Nastavení plovákového spínače
The pump features an adjustable float and rod type switch. Adjust the float to set the desired ON and OFF levels for the pump. Ensure the float can move freely without obstruction within the sump pit.
3.6 Elektrické připojení
Plug the 8 ft. power cord with a grounded plug into a properly grounded 115V AC electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI).
4. Návod k obsluze
The Everbilt SCN250-LQ pump operates automatically based on the water level in the sump pit, controlled by its adjustable float switch.
4.1 Automatický provoz
Once properly installed and plugged in, the pump will turn on automatically when the water level rises and lifts the float switch to the 'ON' position. It will continue to pump water until the level drops and the float switch reaches the 'OFF' position.
4.2 Výkon
This 1/3 HP pump is capable of moving up to 2,400 gallons per hour (GPH) at a 10-foot lift. Its non-corrosive thermoplastic reinforced housing and heavy-duty, high-efficiency permanent split capacitor motor with thermal overload protector ensure reliable performance.
5. Údržba
Regular maintenance helps ensure the longevity and efficient operation of your sump pump.
- Měsíční kontrola: Periodically check the sump pit for any accumulation of debris, dirt, or sediment that could obstruct the pump's inlet or the float switch.
- Kontrola plovákového spínače: Manually lift the float switch to ensure it moves freely and activates the pump. The pump should turn on when the float is raised and turn off when it is lowered.
- Výtlačné potrubí: Verify that the discharge pipe is clear and free of obstructions. Ensure the check valve (if installed) is functioning correctly.
- Těleso čerpadla: Inspect the pump's thermoplastic housing for any signs of damage or cracks.
- Napájecí kabel: Check the power cord for any fraying, cuts, or damage. Replace if necessary.
6. Řešení problémů
If your Everbilt SCN250-LQ pump is not operating as expected, refer to the following common issues and solutions:
| Problém | Možná příčina | Řešení |
|---|---|---|
| Čerpadlo neběží | Čerpadlo není napájeno | Check if the power cord is securely plugged in. Verify the circuit breaker or GFCI has not tripped. |
| Plovákový spínač je zaseknutý nebo zablokovaný | Clear any debris around the float switch and ensure it moves freely. | |
| Thermal overload protector tripped | Allow the pump to cool down. The protector will reset automatically. Check for causes of overheating (e.g., continuous running, low voltagE). | |
| Čerpadlo běží, ale nečerpá vodu | Clogged inlet or discharge pipe | Disconnect power and clear any obstructions from the pump inlet or discharge line. |
| Airlock in the pump | Ensure the pump is fully submerged and there is no air trapped in the system. Briefly unplug and replug the pump to attempt to clear an airlock. | |
| Čerpadlo cykluje příliš často | Float switch adjustment incorrect | Adjust the float switch to increase the distance between the ON and OFF points. |
| Zkontrolujte netěsnost ventilu | Inspect or replace the check valve in the discharge line. |
7. Specifikace
| Funkce | Specifikace |
|---|---|
| Číslo modelu | SCN250-LQ |
| koňská síla (HP) | 1/3 HP (0.33 HP) |
| svtage | 115V AC |
| Ampvymazat | 4.0 Amps |
| Discharge Flow @ 0 ft. | 3550 XNUMX GPH |
| Discharge Flow @ 10 ft. | 2400 XNUMX GPH |
| Discharge Flow @ 15 ft. | 1680 XNUMX GPH |
| Typ spínače čerpadla | Vertical (Adjustable float and rod) |
| Ponorné | Žádný |
| Sump Pump Outlet Diameter Type | 1-1/4 FPT |
| Samonasávací | Ano |
| Maximální pracovní teplota | 95 °F (35 °C) |
| Minimální pracovní teplota | 35 °F (1.7 °C) |
| Materiál bydlení | Termoplast |
| Délka kabelu | 8 stop |
| Hmotnost produktu | 11.44 lb |
| Bateriová záloha | Žádný |
| Certifikace a výpisy | Uvedeno CSA |
| Fits Sump Pit Diameter | 12 in. or larger |
8. Záruka
This Everbilt SCN250-LQ Pedestal Sump Pump comes with a 1 rok záruka from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, misuse, abuse, or unauthorized repairs.
9. Podpora
For technical assistance, replacement parts, or warranty inquiries, please contact Everbilt customer support. Refer to the contact information provided with your product packaging or visit the official Everbilt webstránky pro další podrobnosti.