Návod k obsluze sady klece/základní desky HPE 768857-B21 8-SFF

1. Úvod

This manual provides detailed instructions for the installation, operation, and maintenance of the HPE 768857-B21 8-SFF Cage/Backplane Kit. This kit is designed to expand storage capabilities in compatible HPE ProLiant DL360 Gen9 and DL380 Gen9 servers by providing an additional 8 Small Form Factor (SFF) drive bays. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

Image 1.1: The HPE 8-SFF Cage/Backplane Kit, showing the internal SAS connectors for eight small form factor drives.

2. Bezpečnostní informace

Always observe the following safety precautions when handling and installing the HPE 8-SFF Cage/Backplane Kit:

• Ochrana proti elektrostatickému výboji (ESD): Always use an ESD wrist strap and work on an ESD-safe surface when handling server components to prevent damage.
• Odpojení napájení: Before opening the server chassis or installing any components, ensure the server is powered off and disconnected from all power sources.
• Kompatibilita komponent: Verify that the kit is compatible with your specific server model (ProLiant DL360 Gen9, DL380 Gen9).
• Správná manipulace: Handle the backplane and cage by their edges to avoid touching sensitive electronic components.
• Větrání: Ensure proper airflow within the server chassis after installation to prevent overheating.

3. Obsah balení

The HPE 768857-B21 8-SFF Cage/Backplane Kit package typically includes the following items:

• Storage drive cage - 2nd HDD bay
• Associated cabling (SAS/SATA data and power cables, if applicable)

Image 3.1: The HPE 8-SFF Cage/Backplane Kit, shown with typical associated cabling.

4. Nastavení a instalace

Follow these steps to install the HPE 8-SFF Cage/Backplane Kit into your compatible ProLiant server:

1. Prepare the Server:
   • Power down the server and disconnect all power cords.
   • Remove the server from the rack, if necessary, and place it on a stable, ESD-safe surface.
   • Open the server access panel.
2. Locate the 2nd HDD Bay: Identify the designated bay for the 2nd HDD cage. Refer to your server's specific service manual for exact location and instructions on removing any existing blanks or components.
3. Install the Drive Cage:
   • Carefully align the HPE 8-SFF Cage/Backplane Kit with the bay.
   • Slide the cage into the bay until it clicks securely into place. Ensure all mounting screws or latches are engaged.
4. Připojit kabely:
   • Connect the necessary SAS/SATA data cables from the backplane to the server's RAID controller or motherboard.
   • Connect any required power cables to the backplane from the server's power distribution board.
   • Ensure all cable connections are firm and properly routed to avoid obstructing airflow.
5. Close the Server:
   • Replace the server access panel.
   • Return the server to the rack, if applicable.
   • Reconnect all power cords and power on the server.
6. Instalace disků: Once the server is powered on and the operating system has loaded, you can install your SFF hard drives or solid-state drives into the newly installed cage.

5. Návod k obsluze

This section outlines the basic operation of the HPE 8-SFF Cage/Backplane Kit, primarily focusing on drive installation and removal.

5.1. Installing Drives

1. Ensure the server is powered on and the drive bay is accessible.
2. Slide the SFF drive (mounted in a compatible drive carrier/caddy) into an empty bay in the cage.
3. Push the drive firmly until it seats correctly and the drive carrier latch engages.
4. The server's operating system or RAID controller utility should detect the new drive.

Obrázek 5.1: Bývalýample of a Small Form Factor (SFF) hard drive mounted in a compatible drive caddy, ready for insertion into the cage.

5.2. Removing Drives

1. If the drive is part of a RAID array, ensure it is properly offline or marked for removal within the RAID controller utility or operating system.
2. Press the release latch on the drive carrier.
3. Gently pull the drive carrier out of the bay.
4. Replace with a new drive or a blank filler panel to maintain proper airflow.

6. Údržba

The HPE 8-SFF Cage/Backplane Kit requires minimal maintenance. Adhere to the following guidelines:

• Čištění: Periodically inspect the server's interior for dust accumulation. Use compressed air to gently clean the cage and backplane, ensuring the server is powered off and disconnected from power before cleaning.
• Aktualizace firmwaru: Ensure your server's system ROM and RAID controller firmware are kept up-to-date, as these updates may include improvements for storage subsystem compatibility and performance.
• Fyzická kontrola: Regularly check for any loose cables or connections within the server chassis.

7. Řešení problémů

If you encounter issues with your HPE 8-SFF Cage/Backplane Kit, consider the following troubleshooting steps:

7.1. Drives Not Detected

• Zkontrolujte připojení: Verify that all SAS/SATA data and power cables are securely connected to the backplane and the server's controller/power supply.
• Reseat the Cage: Power down the server and reseat the 8-SFF cage in its bay to ensure it is properly seated.
• Kompatibilita disku: Confirm that the installed drives are compatible with your server and RAID controller.
• RAID Controller Configuration: Check the RAID controller's BIOS or utility to see if the drives are detected there. Configure new drives as needed.

7.2. Problémy s výkonem

• Integrita kabelu: Inspect data cables for damage. Replace if necessary.
• Stav disku: Check the health status of individual drives using diagnostic tools.
• Firmware: Ensure all relevant firmware (server, RAID controller, drive) is up-to-date.

7.3. Fyzické poškození

• If the cage or backplane appears physically damaged, contact HP support for assistance. Do not attempt to repair damaged components yourself.

8. Specifikace

Key technical specifications for the HPE 768857-B21 8-SFF Cage/Backplane Kit:

9. Záruka a podpora

For warranty information and technical support regarding your HPE 768857-B21 8-SFF Cage/Backplane Kit, please refer to the official HP (HPE) website or contact their customer support directly. Keep your purchase receipt and product serial number handy when seeking support.

You can typically find support resources and contact information on the official Podpora HPE webmísto.