1. Úvod
This manual provides detailed instructions for the installation, operation, and maintenance of your Hager EK570 battery-powered weekly thermostat. Please read this guide thoroughly before use to ensure proper function, safety, and to maximize the benefits of its programmable features. Keep this manual for future reference.
2. Bezpečnostní informace
- Always disconnect power to the heating system before attempting any installation or maintenance.
- Installation should only be performed by a qualified electrician or competent person.
- Do not expose the thermostat to extreme temperatures, direct sunlight, high humidity, or water.
- Use only LR6 (AA) batteries as specified. Do not mix old and new batteries or different types of batteries.
- Udržujte zařízení mimo dosah dětí.
- Do not attempt to open or repair the thermostat yourself. Refer to qualified service personnel.
3. Obsah balení
Ověřte, zda jsou v balení přítomny všechny položky:
- Hager EK570 Thermostat Unit
- 2 x LR6 (AA) Batteries
- Montážní šrouby a hmoždinky (pokud jsou k dispozici)
- Tato uživatelská příručka
4. Konec produktuview
Familiarize yourself with the components of your Hager EK570 thermostat:
Obrázek 1: Přední strana view of the Hager EK570 thermostat. The device features a clear LCD display at the top, two square buttons below the display, and a central control cluster at the bottom with '-', 'OK', and '+' buttons.
- LCD displej: Zobrazuje aktuální teplotu, čas, den, provozní režim a stav programu.
- Ovládací tlačítka: Used for navigating menus, adjusting settings, and selecting modes. Typically includes 'Mode', 'Set', 'Up', 'Down', and 'OK' buttons.
- Přihrádka na baterie: Nachází se na zadní straně jednotky.
5. Nastavení
5.1. Instalace baterie
- Remove the back cover of the thermostat.
- Insert the 2 x LR6 (AA) batteries, ensuring correct polarity (+/-).
- Replace the back cover. The display should now activate.
5.2. Montáž termostatu
The Hager EK570 is designed for surface mounting.
- Choose a suitable location on an interior wall, away from direct sunlight, drafts, and heat sources (e.g., radiators, lamps). The recommended height is approximately 1.5 meters from the floor.
- Carefully detach the front part of the thermostat from its base plate.
- Mark the drilling points on the wall using the base plate as a template.
- Vyvrtejte otvory a vložte hmoždinky.
- Připevněte základní desku ke zdi pomocí dodaných šroubů.
- Connect the heating system wires to the terminals on the base plate according to the wiring diagram provided with your heating system. Ensure all connections are secure and correct.
- Reattach the front part of the thermostat to the base plate, ensuring it clicks securely into place.
5.3. Počáteční nastavení (čas a datum)
Upon first power-up or after battery replacement, you may need to set the current time and day.
- Press the 'SET' or 'MODE' button to enter the settings menu.
- Use the '+' or '-' buttons to navigate to 'Time' or 'Date' settings.
- Press 'OK' to confirm and then use '+' or '-' to adjust the values (hour, minute, day, month, year).
- Press 'OK' to save each setting and exit the menu.
6. Návod k obsluze
The Hager EK570 offers various operating modes and programming options to optimize your heating.
6.1. Výběr provozních režimů
The thermostat supports the following modes:
- Komfortní režim: Maintains a comfortable temperature (e.g., 21°C) during occupied periods.
- Omezený režim: Maintains a lower, energy-saving temperature (e.g., 18°C) during unoccupied periods or at night.
- Režim ochrany proti mrazu: Udržuje minimální teplotu (např. 5 °C), aby se zabránilo zamrznutí potrubí.
- Manuální režim: Allows you to set a constant temperature that overrides any programmed schedule.
- Režim dovolené: Maintains a specific temperature for an extended period (e.g., during vacation).
To switch between modes, press the 'MODE' button repeatedly until the desired mode is displayed.
6.2. Adjusting Temperature Setpoint
In any operating mode (except Frost Protection), you can temporarily adjust the temperature setpoint:
- Use the '+' or '-' buttons to increase or decrease the desired temperature.
- The new setpoint will be active until the next programmed event or until you manually change it again. This is known as a temporary override.
6.3. Týdenní programování
The EK570 is a weekly programmable thermostat, allowing you to set up to 48 program steps per day across 4 setpoints (Comfort, Reduced, etc.). It comes with 3 pre-recorded programs and 1 free program for customization.
- Press the 'PROG' or 'SET' button to enter programming mode.
- Use '+' or '-' to select the day of the week you wish to program (e.g., Monday, Tuesday, etc.).
- Press 'OK' to confirm the day.
- The display will show the first program period. Use '+' or '-' to set the start time and then 'OK'.
- Next, select the desired operating mode (Comfort, Reduced, etc.) for this period using '+' or '-' and confirm with 'OK'.
- Repeat steps 4 and 5 for all desired program periods for that day.
- You can copy programs from one day to another if needed (refer to specific instructions in the full manual for this feature).
- Exit programming mode by pressing 'PROG' or 'MODE' button.
7. Údržba
7.1. Čištění
Vyčistěte termostat casing with a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical agents, as these can damage the plastic and electronic components.
7.2. Výměna baterie
The thermostat is powered by 2 x LR6 (AA) batteries. When the battery symbol appears on the display, or if the display becomes dim, it is time to replace the batteries.
- Remove the back cover of the thermostat.
- Vyjměte staré baterie.
- Insert new 2 x LR6 (AA) batteries, observing correct polarity.
- Nasaďte zadní kryt.
The thermostat has a power reserve of approximately 10 minutes, allowing for battery replacement without losing programmed settings, provided the replacement is done promptly.
8. Řešení problémů
| Problém | Možná příčina | Řešení |
|---|---|---|
| Displej je prázdný nebo tmavý. | Baterie jsou slabé nebo nesprávně vložené. | Replace batteries with new LR6 (AA) batteries, ensuring correct polarity. |
| Termostat nereguluje vytápění. | Incorrect wiring; heating system fault; thermostat in 'OFF' or 'Frost Protection' mode. | Check wiring connections (consult a professional); verify heating system power; ensure thermostat is in an active heating mode (Comfort, Reduced, Manual). |
| Naměřená teplota se zdá být nepřesná. | Umístění termostatu je ovlivněno průvanem, přímým slunečním zářením nebo zdroji tepla. | Přemístěte termostat na vhodnější místo, mimo dosah vnějších vlivů. |
| Cannot program the thermostat. | Incorrect programming steps followed; thermostat locked. | Refer to Section 6.3 for programming instructions. Check if a child lock feature is active (consult full manual). |
9. Specifikace
| Funkce | Specifikace |
|---|---|
| Model | EK570 |
| Napájení | 2 x LR6 (AA) Batteries (included) |
| Setpoint Adjustment Range | 5 °C až 30 °C |
| Provozní teplota | 0 °C až 45 °C |
| Skladovací/přepravní teplota | -25 °C až 70 °C |
| Typ zobrazení | LCD s podsvícením |
| Typ hodin | Digitální termostat |
| Typ snímače | Elektronický |
| Typ montáže | Povrchová montáž |
| Typ terminálu | 1 až 1.5 mm² |
| Rated Operating Current (AC1) | 5 A |
| Breaking Capacity | 5 A / 250 V |
| Hodnocení ochrany IP | IP30 |
| Záloha | 10 minut |
| Ecodesign Class | 4 |
| Rozměry (přibližné) | 97 mm (výška) x 70 mm (šířka) x 30 mm (hloubka) |
| Hmotnost (přibližná) | 340 gramů (včetně obalu) |
10. Záruka a podpora
For detailed warranty information, technical support, or service inquiries, please refer to the official Hager webnebo se obraťte na autorizovaného prodejce. Uschovejte si účtenku jako doklad o koupi.
