Výměna osvětlení Boxlight Lamp Uživatelský manuál modulu

Důležité bezpečnostní informace

Žárovka v tomto lamp contains Mercury (Hg). Please dispose of in accordance with local, state, or federal laws. Do not dispose of with regular household waste.

• Always disconnect the projector from the power outlet before attempting any installation or maintenance.
• Allow the projector to cool down completely (at least 30 minutes) before replacing the lampHorké lampmůže způsobit těžké popáleniny.
• Avoid touching the glass surface of the new lamp directly with bare hands. Oils from your skin can reduce lamp život. V případě potřeby použijte rukavice nebo čistý hadřík.
• Netlačte silou lamp module into place. If it does not fit easily, recheck the orientation and ensure it is the correct lamp for your projector model.
• Nikdy nepoužívejte projektor samp kryt odstraněn.
• Nechte si lamp module out of reach of children.

Pokyny k instalaci

1. Vypnutí a odpojení: Ensure your Boxlight projector is turned off and completely unplugged from the power source.
2. Ochladit: Allow the projector to cool down for at least 30 minutes. The lamp operates at high temperatures and can cause burns if handled while hot.
3. Vyhledejte L.amp Pokrýt: Refer to your projector's user manual to locate the lamp compartment cover. This is typically secured by one or more screws.
4. Odstraňte Lamp Pokrýt: Using a suitable screwdriver, carefully remove the screw(s) securing the lamp cover and then remove the cover.
5. Unscrew Old Lamp: Starý lamp module will be secured by one or more screws. Unscrew these fasteners.
6. Odstraňte staré Lamp: Gently pull the handle on the old lamp module to slide it out of the projector. Be careful not to drop it.
7. Vložit nové Lamp: Carefully insert the new Boxlight replacement lamp module into the projector, ensuring it slides smoothly into place. Do not force it.
8. Bezpečné nové Lamp: Fasten the new lamp module with the screw(s) you removed earlier. Ensure it is securely seated.
9. Vyměňte Lamp Pokrýt: Znovu připojte lamp kryt přihrádky a zajistěte jej šroubem (šrouby).
10. Znovu připojte napájení: Zapojte projektor zpět do elektrické zásuvky.
11. Resetovat Lamp Časovač: Consult your projector's user manual for instructions on how to reset the lamp timer. This is crucial for accurate lamp life tracking.

Provozní směrnice

• Správné vypnutí: Always allow the projector to complete its cooling cycle after use before unplugging it. Abrupt power cuts can shorten lamp život.
• Větrání: Ensure the projector has adequate ventilation. Blocked vents can lead to overheating and reduced lamp život.
• Vyhněte se častým cyklům zapínání/vypínání: Turning the projector on and off frequently can stress the lamp a zkrátit jeho životnost.
• Eco Mode (if available): If your projector has an "Eco Mode" or similar power-saving setting, using it can extend lamp život.

Údržba

• Čištění vzduchového filtru: Regularly clean or replace your projector's air filter as per your projector's manual. A clogged filter can cause the projector to overheat, negatively impacting lamp život.
• Odstranění prachu: Keep the projector free from dust. Use a soft, dry cloth to wipe the exterior. Do not use abrasive cleaners or solvents.
• Lamp Zacházení: Při manipulaci s lamp module, always hold it by its housing, not the bulb itself.

Odstraňování problémů

Pokud se po instalaci nového l setkáte s problémyamp, zvažte následující:

• Lamp Nesvítí:
  • Ujistěte se, že lamp Modul je zcela usazen a zajištěn šrouby.
  • Ověřte lamp cover is correctly installed and secured. Many projectors have a safety switch that prevents operation if the cover is open.
  • Check that the projector is properly plugged into a working power outlet.
• Dim Image or Poor Color:
  • Potvrďte lamp timer has been reset. If not, the projector might still be operating under the assumption of an old, worn-out lamp.
  • Check projector settings for brightness or picture modes.
  • Ujistěte se, že je čočka projektoru čistá.
• "Lamp Error" Message:
  • This often indicates the lamp is not properly installed or the lamp cover is not secured. Re-check installation steps.
  • If the error persists, the lamp itself might be faulty. Contact customer support.

For further assistance, refer to your projector's original user manual or contact Boxlight customer support.

Specifikace produktu

Informace o záruce

This Boxlight replacement lamp module is covered by a Záruka 180-Day od data nákupu. Tato záruka se vztahuje na vady materiálu a zpracování při běžném používání. Uschovejte si prosím doklad o koupi pro případ uplatnění záruky.

For warranty service or inquiries, please contact the seller or manufacturer directly.

Zákaznická podpora

If you require further assistance, have questions about installation, or need to report an issue, please contact the retailer where you purchased this product or the manufacturer, Arclyte Tech. (Boxlight's manufacturer).

When contacting support, please have your product model number (ACTG042) and proof of purchase readily available.