Uživatelská příručka k samonasávacímu filtračnímu čerpadlu Steinbach SPS 100-1T

1. Konec produktuview

The Steinbach SPS 100-1T self-priming filter pump is designed to be the central component of your pool's circulation system. This robust pump features a pre-filter and an integrated timer, making it suitable for pools up to approximately 40,000 liters (10,567 gallons) in volume. It operates on 230V/550W power and offers a pumping capacity of 9,480 liters per hour (158 l/min) with a maximum pump height of 10 meters.

The pump is designed for durability and efficiency, ensuring clean and clear pool water. It is compatible with hose connections of Ø 32/38 mm and can operate with water temperatures up to 35 °C.

Obrázek 1: Přesview of the Steinbach SPS 100-1T Self-Priming Filter Pump. This image shows the complete pump unit, including the motor, pump housing, and pre-filter basket.

2. Bezpečnostní pokyny

• Před prováděním jakékoli údržby nebo čištění vždy odpojte čerpadlo od napájení.
• Ensure the pump is installed on a stable, level surface to prevent vibration and movement.
• Do not operate the pump dry. Ensure it is always filled with water before starting.
• Během provozu držte děti a domácí zvířata v dostatečné vzdálenosti od čerpadla.
• Only use the pump for its intended purpose (pool water filtration).
• Regularly inspect the power cable for damage. Do not use if damaged.
• Ensure all electrical connections are properly sealed and protected from water.

3. Nastavení a instalace

3.1 Vybalení

Opatrně vyjměte všechny součásti z obalu. Zkontrolujte, zda jsou všechny součásti přítomny a nepoškozené. Úplný inventář naleznete v dodacím listu.

3.2 Umístění

Position the pump on a firm, level surface, preferably below the water level of the pool for optimal self-priming. Ensure adequate ventilation around the pump to prevent overheating. The pump should be placed in a location protected from direct sunlight and adverse weather conditions.

3.3 Připojení hadic

Connect the pool's suction line to the inlet of the pump (the side with the pre-filter) and the return line to the outlet. The pump is designed for Ø 32/38 mm hose connections. Secure all hose connections with appropriate clamps, aby se zabránilo únikům.

Obrázek 2: Detail view of the pre-filter inlet with a hose connected. This shows the transparent pre-filter housing and the connection point for the pool's suction hose.

Obrázek 3: Detail view of the pump outlet with a hose connected. This illustrates the connection point for the pool's return hose.

3.4 Naplnění čerpadla

Before first use, or after the pump has been drained, it must be primed. Open the pre-filter lid and fill the pre-filter basket and pump housing completely with water. Replace the lid securely. This ensures the pump does not run dry, which can cause damage.

Obrázek 4: View of the pre-filter inlet without a hose attached. This shows the threaded connection for the pre-filter housing.

Obrázek 5: View of the pump outlet without a hose attached. This shows the threaded connection for the outlet hose.

3.5 Elektrické připojení

Connect the pump to a grounded 230V power outlet. Ensure the electrical circuit is protected by a Residual Current Device (RCD) for safety. Do not use extension cords unless absolutely necessary, and ensure they are rated for outdoor use and the pump's power requirements.

4. Návod k obsluze

4.1 Starting and Stopping the Pump

Once the pump is primed and all connections are secure, press the ON/OFF button on the control panel to start the pump. Press it again to stop the pump.

4.2 Using the Integrated Timer

The SPS 100-1T pump features an integrated timer for automated operation. Use the ČASOVAČ button to set the desired operating duration. The control panel typically has indicators for various time settings (e.g., 2, 4, 6, 8, 10, 12, 14, 16, 24 hours). Select the appropriate duration based on your pool's size and usage to ensure adequate filtration.

Obrázek 6: Detail view of the pump's control panel. This image highlights the ON/OFF and TIMER buttons, along with the indicators for setting the filtration duration.

4.3 Optimal Filtration Time

For optimal water quality, it is generally recommended to filter the entire volume of your pool water at least once per day. The required filtration time depends on the pump's flow rate and your pool's volume. For this pump with a flow rate of 9,480 l/h, a 40,000-liter pool would require approximately 4.2 hours of filtration per day (40,000 L / 9,480 L/h ≈ 4.2 h).

5. Údržba

5.1 Čištění předfiltračního koše

The pre-filter basket collects larger debris and should be cleaned regularly to maintain pump efficiency.

1. Vypněte čerpadlo a odpojte jej od napájení.
2. Odšroubujte průhledné víko předfiltru.
3. Remove the pre-filter basket and empty any collected debris.
4. Rinse the basket thoroughly with clean water.
5. Zkontrolujte O-kroužek na víku, zda není poškozený, a ujistěte se, že je čistý.
6. Place the clean basket back into the housing and securely screw on the lid.
7. V případě potřeby před opětovným spuštěním čerpadlo znovu naplňte.

5.2 Zazimování

Before the first frost, the pump must be drained and stored in a frost-free environment.

• Odpojte čerpadlo od napájení.
• Odpojte všechny hadice.
• Remove the drain plug (if present) or tilt the pump to ensure all water drains out.
• Vyčistěte vnější část čerpadla.
• Čerpadlo skladujte na suchém místě chráněném před mrazem.

6. Řešení problémů

7. Technické specifikace

8. Záruka a podpora

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, spare parts, or warranty claims, please contact Steinbach customer service or your authorized dealer.

Steinbach Contact Information:

• Webmísto: www.steinbach.at
• Reference modelu: 9008748409179

Před kontaktováním podpory si prosím připravte číslo modelu (040917) a datum nákupu.