Uživatelská příručka k neprogramovatelnému termostatu QuietWarmth THERMST-D

1. Úvod

The QuietWarmth THERMST-D Non-Programmable Thermostat is designed to provide reliable control for 120V or 240V electric radiant floor heating systems. This thermostat offers flexible temperature management, allowing you to configure it for control based on floor temperature, room temperature, or a combination of room temperature with a floor temperature limit. It features a built-in Ground Fault Circuit Interrupter (GFCI) for enhanced safety and a clear, backlit display for easy monitoring and operation. A floor sensor is included to ensure accurate temperature readings and optimal comfort.

Obrázek 1: Přední strana view of the THERMST-D Thermostat.

2. Bezpečnostní informace

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or property damage.

• VAROVÁNÍ: To reduce the risk of electric shock, do not connect this device to a circuit with any phase operating down more than 150 volts to ground.
• Instalaci musí provést kvalifikovaný elektrikář v souladu s místními a národními elektrotechnickými předpisy.
• The thermostat requires connection to a dedicated 20 Amp obvod.
• The resistive load connected to the thermostat must not exceed 15 Amps.
• Electric radiant floor heating systems are required by the National Electrical Code to be protected by a Ground Fault Circuit Interrupter (GFCI). This thermostat has a built-in GFCI.
• Před instalací nebo servisem termostatu vždy vypněte napájení jističem.

Obrázek 2: Strana view of the thermostat with safety warning label.

3. Obsah balení

Ověřte, zda jsou v balení přítomny všechny položky:

• QuietWarmth THERMST-D Non-Programmable Thermostat
• Podlahový senzor

4. Konec produktuview

4.1 Klíčové vlastnosti

• Non-Programmable operation for radiant floor heat systems.
• Compatible with both 120V and 240V heating systems.
• Integrated Ground Fault Circuit Interrupter (GFCI) for safety.
• Clear, backlit LED display for easy reading.
• Includes a floor sensor for precise temperature control.
• Configurable for floor temperature, room temperature, or room temperature with a floor temperature limit.
• Seven-day energy log to monitor power consumption.
• Supports multiple QuietWarmth mats: up to 120 sq ft for 120V systems, or 240 sq ft for 240V systems.

4.2 Komponenty

The thermostat consists of a front display unit with control buttons and a back plate for electrical connections.

• Přední panel: Features a digital display showing time and temperature, along with 'Up', 'OK', and 'Down' buttons for navigation and setting adjustments.
• Zadní panel: Contains wiring terminals for power input (L1, L2) and load output, as well as a connection point for the floor sensor.

Obrázek 3: Zpět view of the thermostat with wiring terminals.

Figure 4: Included floor sensor.

5. Nastavení a instalace

Instalaci by měl provádět pouze kvalifikovaný elektrikář.

5.1 Montáž

• The thermostat is designed for wall mounting.
• Ensure the mounting location is free from direct sunlight, drafts, or other heat sources that could affect temperature readings.

5.2 Zapojení

Before wiring, ensure power is OFF at the circuit breaker.

1. Connect the thermostat to a dedicated 20 Amp obvod.
2. Identify the Line (power supply) and Load (heating mat) wires.
3. Connect the Line wires to the L1(L) and L2(N) terminals on the thermostat's back panel.
4. Connect the Load wires from the heating mat to the 'Load' terminals on the thermostat.
5. Zajistěte správné uzemnění v souladu s místními elektrotechnickými předpisy.
6. The thermostat is dual-voltage; it can be used with either 120V or 240V heating mats, but not simultaneously. Verify your heating mat's voltage odpovídá napájení.

5.3 Floor Sensor Placement

The floor sensor is crucial for accurate floor temperature control.

• Place the sensor next to the long edge of the QuietWarmth heating mat.
• Ensure the sensor is positioned in the heated area and not near any unheated zones or external heat sources.
• Route the sensor wire carefully to avoid damage during installation of flooring materials.

Obrázek 5: Přample of radiant heat film installation under floating floors.

Obrázek 6: Přample of radiant heat film installation under tile and glued floors.

6. Návod k obsluze

6.1 Zapnutí

After installation, restore power at the circuit breaker. The thermostat display will illuminate.

6.2 Nastavení teploty

• Použijte Up a Dolů tlačítka pro nastavení požadované teploty.
• Stiskněte tlačítko OK potvrďte svůj výběr.

6.3 režimy ovládání

The thermostat can be configured to operate in one of three control modes:

• Floor Temperature Control: The thermostat maintains the floor at the set temperature using the floor sensor.
• Ovládání pokojové teploty: The thermostat maintains the room air temperature at the set point.
• Room Temperature Control with Floor Limit: The thermostat primarily controls room air temperature but prevents the floor temperature from exceeding a specified maximum limit, protecting sensitive flooring materials.

Refer to the full installation guide for instructions on how to select and configure these control modes.

6.4 Energy Log

The thermostat features a seven-day energy log, allowing you to monitor the power consumption of your radiant heating system. Consult the detailed manual for accessing and interpreting this data.

7. Údržba

7.1 Testování proudového chrániče (GFCI)

For continued safety, the built-in GFCI should be tested monthly.

1. Stiskněte tlačítko TEST button located on the bottom of the thermostat.
2. The GFCI should trip, cutting power to the heating system and indicating a fault.
3. Stiskněte tlačítko RESETOVAT button to restore power.
4. If the GFCI does not trip or reset correctly, discontinue use and contact a qualified electrician.

Figure 7: Bottom of the thermostat with GFCI test button.

7.2 Čištění

Otřete vnější část termostatu měkkým hadříkemamp tkanina. Nepoužívejte abrazivní čisticí prostředky nebo rozpouštědla.

8. Řešení problémů

If you encounter issues with your QuietWarmth THERMST-D thermostat, refer to the following common problems and solutions:

• Žádný displej/Žádné napájení:
  • Check the circuit breaker for the dedicated circuit and ensure it is in the ON position.
  • Zkontrolujte, zda jsou všechna zapojení kabeláže bezpečná a správná.
• Topný systém se neaktivuje:
  • Ensure the thermostat is set to a temperature higher than the current room or floor temperature.
  • Check if the GFCI has tripped (press the RESET button if it has).
  • Confirm the correct control mode is selected (floor, room, or room with limit).
• GFCI Trips Frequently:
  • This indicates a ground fault. Immediately turn off power at the circuit breaker.
  • Inspect the heating mat and wiring for any damage or moisture.
  • Ensure the total resistive load does not exceed 15 Amps.
  • Contact a qualified electrician for diagnosis and repair.
• Nepřesné údaje o teplotě:
  • Verify the floor sensor is correctly installed and not damaged.
  • Ensure the thermostat is not exposed to drafts, direct sunlight, or other external heat sources.

For issues not covered here, please contact QuietWarmth customer support or a qualified electrician.

9. Specifikace

10. Záruka a podpora

10.1 Informace o záruce

The QuietWarmth THERMST-D Non-Programmable Thermostat comes with a 3-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

10.2 Zákaznická podpora

For technical assistance, troubleshooting, or warranty inquiries, please contact QuietWarmth customer support. Refer to the product packaging or the manufacturer's webstránky s aktuálními kontaktními informacemi.