Uživatelská příručka k dobíjecí digitální LED svítilně JetBeam DDR-26 XM-L2

1. Úvod

Thank you for choosing the JetBeam DDR-26 XM-L2 Rechargeable Digital Display LED Flashlight. This manual provides detailed instructions for the proper use, setup, operation, and maintenance of your new flashlight. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

2. Konec produktuview

The JetBeam DDR-26 is a high-performance, rechargeable LED flashlight featuring an advanced XM-L2 LED and a convenient digital display. Its robust design and versatile functionality make it suitable for various applications.

3. Nastavení

3.1 Instalace baterie

The JetBeam DDR-26 requires 1 CR123A battery (or compatible rechargeable battery). To install the battery:

1. Odšroubujte zadní krytku svítilny otáčením proti směru hodinových ručiček.
2. Vložte baterii kladným (+) pólem směrem k hlavě svítilny.
3. Zašroubujte zadní krytku zpět ve směru hodinových ručiček, dokud nebude bezpečně utažena. Ujistěte se, že O-kroužek je správně usazen, aby byla zachována vodotěsnost.

3.2 Nabíjení

The DDR-26 features a built-in charging port (refer to Figure 2.5). To charge the flashlight:

1. Locate the charging port cover on the side of the flashlight and gently lift it to expose the port.
2. Connect the appropriate charging cable (not specified in product data, assume standard DC 5V) to the port and a compatible power source.
3. The digital display will typically indicate the charging status.
4. Once charging is complete, disconnect the cable and securely close the charging port cover to protect it from dust and water.

4. Návod k obsluze

4.1 Zapnutí/vypnutí

To turn the flashlight on or off, press the main power button located near the digital display (refer to Figure 2.3).

4.2 Výběr režimu

While the flashlight is on, press the power button repeatedly to cycle through different brightness modes (e.g., Low, Medium, High) and special modes (e.g., Strobe, SOS), if available. The digital display may show the current brightness level or mode.

4.3 Digital Display Functionality

The digital display provides real-time information, which may include:

• Baterie voltage or remaining battery life.
• Current brightness level or output.
• Charging status when connected to a power source.

5. Údržba

5.1 Čištění

Pravidelně čistěte tělo svítilny měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla. Pro optimální světelný výkon udržujte čočku čistou.

5.2 O-Ring Lubrication

To maintain water resistance, periodically inspect and lubricate the O-rings with silicone grease. Replace O-rings if they appear damaged or worn.

5.3 Skladování

If the flashlight will not be used for an extended period, remove the battery to prevent leakage and store the flashlight in a cool, dry place.

6. Řešení problémů

• Svítilna se nezapíná: Check if the battery is installed correctly with the positive end facing the head. Ensure the battery is charged. Tighten the tail cap securely.
• Světlo je tlumené nebo bliká: The battery may be low; recharge or replace it. Ensure battery contacts are clean.
• Digitální displej nefunguje: Ensure the battery is properly installed and charged. If the issue persists, contact customer support.
• Problém s nabíjením: Verify the charging cable is properly connected to both the flashlight and the power source. Ensure the power source is active.

7. Specifikace

8. Záruka a podpora

For warranty information or technical support, please refer to the warranty card included with your product or visit the official JETBeam webwebu. Uschovejte si účtenku jako doklad o koupi.