ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat User Manual

Zavedení

This manual provides detailed instructions for the installation, operation, and maintenance of your ICM Controls SC1600L Simple Comfort Non-Programmable Heat Only Thermostat. This thermostat is designed for use with single-stage heating systems and features a backlit display for easy readability. Please read this manual thoroughly before installation and operation to ensure proper use and to prevent damage to the unit or your heating system.

Bezpečnostní informace

• Always turn off power to the heating system at the main fuse or circuit breaker panel before installing or servicing the thermostat.
• This thermostat is designed for 24 VAC heating systems only. Do not use it with line voltage systémy (120/240 V AC).
• Pokud si nejste jisti některými kroky, měl by instalaci provést kvalifikovaný technik.
• Nezkratujte svorky baterie.
• Zlikvidujte baterie v souladu s místními předpisy.

Obsah balení

• ICM Controls SC1600L Thermostat Control Unit
• Montážní materiál (šrouby a hmoždinky do zdi)
• Uživatelská příručka

Nastavení a instalace

1. Výběr lokality

Termostat instalujte přibližně 1.5 metru nad podlahou v oblasti s dobrou cirkulací vzduchu. Vyhněte se umístění v blízkosti zdrojů tepla (např.amps, sunlight, fireplaces), cold drafts (windows, doors), or areas with poor air circulation.

2. Power Disconnection

Before beginning installation, ensure the power to your heating system is completely turned off at the circuit breaker or fuse box.

3. Demontáž starého termostatu

1. Carefully remove the cover of your old thermostat.
2. Note the wire connections. This thermostat is designed for 2-wire heat-only systems. Typically, these wires are connected to terminals labeled 'R' and 'W'. Take a picture or label the wires for reference.
3. Disconnect the wires and remove the old thermostat's mounting plate from the wall.

4. Montáž nového termostatu

1. Separate the front cover from the backplate of the SC1600L thermostat.
2. Position the backplate against the wall, feeding the wires through the opening. Mark the mounting holes.
3. Drill pilot holes if necessary and secure the backplate to the wall using the provided screws.

5. Zapojení

Connect the two heating system wires to the terminals on the SC1600L backplate. This thermostat typically uses two wires: one for power (often labeled 'R' or 'Rh') and one for the heating call (often labeled 'W'). Ensure connections are secure.

6. Instalace baterie

This thermostat is battery-powered. Insert the required batteries (typically 2 AA batteries, not included) into the battery compartment on the back of the front cover, observing the correct polarity (+/-). The display should illuminate.

7. Attaching the Front Cover

Carefully align the front cover with the mounted backplate and snap it into place.

Image: The ICM Controls SC1600L thermostat installed on a wall, showing its digital display and control buttons.

8. Power Restoration

Restore power to your heating system at the main fuse or circuit breaker panel.

Návod k obsluze

1. Zobrazit přesview

The large digital display shows the current room temperature. When adjusting the setpoint, the desired temperature will be displayed temporarily.

2. Nastavení teploty

• Použijte UP (▲) a DOLŮ (▼) arrow buttons located next to the display to adjust the desired temperature (setpoint).
• Each press of the button will change the setpoint by one degree Fahrenheit.
• Termostat bude automaticky udržovat nastavenou teplotu.

3. System Mode Switch (Off/Heat)

Locate the slide switch at the bottom of the thermostat. This switch controls the system mode:

• OFF: The heating system is turned off. The thermostat will not call for heat.
• TEPLO: The thermostat will operate the heating system to maintain the set temperature.

4. Ovládání podsvícení

The display backlight will activate when any button is pressed, providing improved visibility in low-light conditions. The backlight will automatically turn off after a short period of inactivity.

Obrázek: Podrobný view of the SC1600L thermostat's controls and display.

Údržba

1. Výměna baterie

The thermostat is battery-powered. When the battery icon appears on the display, it indicates that the batteries are low and need to be replaced. To replace batteries:

1. Jemně stáhněte přední kryt termostatu z nástěnné desky.
2. Vyjměte staré baterie a vložte nové, dbejte na správnou polaritu.
3. Snap the front cover back onto the wall plate.

Poznámka: Replacing batteries typically does not affect the set temperature, but it is good practice to verify the setting after replacement.

2. Čištění

Očistěte vnější povrch termostatu měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla. Nestříkejte tekutiny přímo na termostat.

Odstraňování problémů

Specifikace

• Model: SC1600L
• Značka: Ovládací prvky ICM
• Typ ovládání: Neprogramovatelné
• Typ regulace teploty: Topení
• Zdroj napájení: Napájení z baterie
• svtage: 24 voltů
• Typ displeje: LCD s podsvícením
• Způsob ovládání: Ovládání tlačítkem
• Typ materiálu: Plast
• Typ montáže: Montáž na panel

Informace o záruce

ICM Controls products are manufactured to high standards and are backed by a limited warranty. For specific warranty details, including duration and coverage, please refer to the warranty card included with your product or visit the official ICM Controls webUschovejte si doklad o koupi pro případ reklamace.

Podpora

If you have any questions or require technical assistance with your ICM Controls SC1600L thermostat, please contact ICM Controls customer support. Contact information can typically be found on the product packaging or the official ICM Controls webmísto.