Uživatelská příručka k univerzálnímu termostatu BRAEBURN 2020

Zavedení

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Braeburn 2020 Universal Thermostat. This thermostat is designed for single-stage heating or cooling systems, including single-stage heat pumps and 250mv-750mv millivolt heating systems. It offers flexible programming options including 7-day, 5-2 day, or non-programmable modes to suit various scheduling needs.

Bezpečnostní informace

Always turn off power to the heating/cooling system at the main fuse or circuit breaker panel before installing or servicing the thermostat. Read all instructions carefully before proceeding with installation or operation. Improper installation can damage the thermostat or the heating/cooling system.

Obsah balení

• Braeburn 2020 Thermostat Unit
• Wall Plate / Sub-base
• Montážní materiál (šrouby a hmoždinky)
• Alkalické baterie AA (2)
• Uživatelská příručka (tento dokument)

Instalace

1. Vypněte napájení

Before beginning installation, ensure the power to your heating and cooling system is completely turned off at the circuit breaker or fuse box. This prevents electrical shock and damage to the equipment.

2. Demontujte starý termostat

Carefully remove the cover of your old thermostat. Take a picture of the existing wiring connections for reference. Label each wire with the terminal designation it was connected to (e.g., R, W, Y, G, C). Disconnect the wires and remove the old thermostat's mounting plate.

3. Mount New Wall Plate

Position the Braeburn 2020 wall plate against the wall where the old thermostat was located. Use the provided screws and wall anchors to secure the wall plate. Ensure the wires pass through the opening in the wall plate.

4. Zapojte termostat

Connect the labeled wires to the corresponding terminals on the new Braeburn 2020 wall plate. Refer to the wiring diagram below for common configurations. If your old thermostat had a 'C' wire, connect it to the 'C' terminal on the new thermostat for continuous 24V AC power. If no 'C' wire is present, the thermostat will operate on battery power.

Poznámka: Tento termostat je kompatibilní s jednotlivýmitage systems. For heat pump systems, ensure proper configuration in the setup menu.

5. Install Batteries and Attach Thermostat

Insert the two AA alkaline batteries into the battery compartment on the back of the thermostat unit. Align the thermostat with the wall plate and gently push it onto the plate until it snaps securely into place.

6. Obnovte napájení

Return to your main fuse or circuit breaker panel and restore power to your heating and cooling system.

Nastavení a počáteční konfigurace

Upon initial power-up or after a reset, the thermostat will require basic setup.

1. Nastavení aktuálního času a dne

1. Stiskněte tlačítko BĚHEM DNE tlačítko.
2. Použijte UP or DOLŮ arrow buttons to adjust the hour. Press BĚHEM DNE znovu pro potvrzení a přechod na minuty.
3. Použijte UP or DOLŮ arrow buttons to adjust the minutes. Press BĚHEM DNE again to confirm and move to the day of the week.
4. Použijte UP or DOLŮ Pomocí tlačítek se šipkami vyberte aktuální den. Stiskněte NÁVRAT uložit a ukončit.

2. Installer Setup Menu

The installer setup menu allows configuration for specific system types. Consult a qualified HVAC technician if unsure about these settings.

• Typ systému: Configure for conventional (gas/electric) or heat pump systems.
• Provoz ventilátoru: Set fan operation during heating cycles (e.g., gas furnace typically controls its own fan).
• Zobrazení teploty: Vyberte Fahrenheita nebo Celsia.
• Režim programování: Choose 7-day, 5-2 day, or non-programmable.

Obsluha termostatu

Obraz: Přední view of the Braeburn 2020 Universal Thermostat. The display shows "73" and "OFF". Below the display are buttons labeled "PROG", "HOLD", "RETURN", "DAY/TIME". On the left, a slider switch for "SYSTEM" with options "COOL", "OFF", "HEAT". On the right, a slider switch for "FAN" with options "AUTO", "ON". Up and Down arrow buttons are located to the right of the main display.

1. Výběr systémového režimu

Použijte SYSTÉM switch on the left side of the thermostat to select the desired operating mode:

• CHLADNÝ: The thermostat will operate your cooling system.
• OFF: Systémy vytápění a chlazení jsou vypnuty.
• TEPLO: The thermostat will operate your heating system.

2. Výběr režimu ventilátoru

Použijte FAN switch on the right side of the thermostat to select the desired fan operation:

• AUTO: Ventilátor běží pouze tehdy, když je aktivně zapnuto topení nebo chlazení. Toto je nejběžnější nastavení.
• NA: Ventilátor běží nepřetržitě, bez ohledu na to, zda je aktivní systém topení nebo chlazení.

3. Nastavení teploty

In any operating mode (HEAT or COOL), use the UP or DOLŮ arrow buttons to adjust the desired setpoint temperature. The display will show the new setpoint temporarily.

4. Hold Function (Temporary Override)

Stiskněte tlačítko DRŽET button to temporarily override the programmed schedule. The thermostat will maintain the current setpoint temperature indefinitely until the DRŽET button is pressed again or the system mode is changed. The word "HOLD" will appear on the display.

Programming (7-Day or 5-2 Day Modes)

If your thermostat is configured for 7-day or 5-2 day programming, you can set custom schedules for different times of the day and week. The thermostat allows for four program periods per day: Morning, Day, Evening, and Night.

1. Vstup do režimu Program

Stiskněte tlačítko PROG button. The display will show the current program period (e.g., "MORN") and the associated setpoint temperature and time.

2. Nastavení programových období

1. While in program mode, use the BĚHEM DNE button to cycle through the days of the week (for 7-day programming) or between Weekdays (Mon-Fri) and Weekend (Sat-Sun) for 5-2 day programming.
2. Použijte PROG button to cycle through the four program periods (Morning, Day, Evening, Night) for the selected day(s).
3. For each program period, use the UP or DOLŮ arrow buttons to adjust the desired start time and setpoint temperature for both heating and cooling (if applicable).
4. After setting all desired program periods for a day or group of days, press NÁVRAT pro uložení a ukončení programovacího režimu.

3. Adaptive Recovery Mode (ARM)

ARM allows the thermostat to activate the heating or cooling system prior to a scheduled program period to ensure the desired temperature is reached by the start of that period. This feature is typically enabled in the installer setup menu.

4. Temporary Program Override

If you adjust the temperature using the UP or DOLŮ arrow buttons while in normal operating mode (not HOLD), the thermostat will temporarily override the current program setpoint until the next scheduled program period begins. The display will show "TEMP HOLD" or similar indication.

Údržba

1. Výměna baterie

When the low battery indicator appears on the display, replace the two AA alkaline batteries immediately. To replace, gently pull the thermostat unit straight off the wall plate, replace the batteries, and then snap the unit back onto the wall plate. Settings are typically retained during battery replacement due to non-volatile memory.

2. Čištění

Očistěte vnější povrch termostatu měkkým hadříkemamp hadříkem. Nepoužívejte abrazivní čisticí prostředky ani rozpouštědla. Nestříkejte tekutiny přímo na termostat.

3. Filter Check Monitor

The thermostat may include a filter check monitor that reminds you to change your system's air filter. When the "FILTER" indicator appears, change your filter and then press the RESETOVAT button (usually a small recessed button) to clear the reminder.

Odstraňování problémů

If problems persist after attempting these solutions, contact a qualified HVAC technician or Braeburn customer support.

Specifikace

• Model: 2020
• Kompatibilita: Single-stage gas, oil, or electric heating/cooling systems, single-stage heat pumps, 250mv-750mv millivolt heating systems.
• Moc: 24V AC (C-wire) or 2 "AA" Alkaline Batteries (3.0V DC)
• Rozsah regulace teploty: 45 °F až 90 °F (7 °C až 32 °C)
• Přesnost teploty: +/-1 °F (+/- 0.5 °C)
• Rozsah vlhkosti: 5% až 95% relativní vlhkost (bez kondenzace)
• Zobrazit: Bright blue backlight
• Rozměry: Přibližně 3.70 cm V x 5.16 cm Š x 1.38 cm H
• Vlastnosti: Non-volatile memory, adjustable temperature limits, filter check monitor, adaptive recovery mode (ARM), low battery indication, front reset button.

Záruka a podpora

For warranty information or technical assistance, please refer to the official Braeburn website or contact Braeburn customer support directly. Keep your purchase receipt as proof of purchase for warranty claims.

Braeburn Webmísto: www.braeburnonline.com