3M Specialty Adhesive Remover 38987 Instruction Manual

Konec produktuview

The 3M Specialty Adhesive Remover 38987 is a solvent-based product formulated for the effective removal of reactive adhesives from various surfaces. Reactive adhesives are those that require a hardener or catalyst to form a bond, including but not limited to epoxies, urethanes, and silicones.

Image: 3M Specialty Adhesive Remover 38987 in an aerosol can.

Klíčové vlastnosti:

• Specifically designed to remove reactive adhesives.
• Effective on epoxies, urethanes, and silicones.
• Solvent-based formulation for strong adhesive breakdown.
• Suitable for use on a variety of substrates.

Bezpečnostní informace

WARNING: For industrial/occupational use only. Not for consumer sale or use. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage.

This product contains strong solvents. Always read and understand the Safety Data Sheet (SDS) before use. Ensure adequate ventilation during application. Use in a well-ventilated area or outdoors.

Opatření:

• Osobní ochranné prostředky (OOP): Wear appropriate chemical-resistant gloves (e.g., nitrile), eye protection (safety glasses or goggles), and respiratory protection if ventilation is inadequate.
• Hořlavost: Keep away from heat, sparks, open flames, and hot surfaces. No smoking.
• Kontakt s kůží: Zabraňte delšímu nebo opakovanému kontaktu s kůží. Po manipulaci důkladně omyjte mýdlem a vodou.
• Oční kontakt: In case of contact, rinse immediately with plenty of water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Seek medical attention if irritation persists.
• Inhalace: Avoid breathing vapors. If inhaled, remove to fresh air. If symptoms persist, seek medical attention.
• Požití: Do not ingest. If swallowed, do NOT induce vomiting. Call a poison center or doctor immediately.
• Skladování: Store in a cool, well-ventilated place. Keep container tightly closed. Keep out of reach of children.
• Kompatibilita povrchu: Always test on an inconspicuous area first to ensure compatibility with the substrate, as some surfaces (e.g., certain plastics, painted finishes) may be damaged by solvents.

Nastavení

Before beginning the adhesive removal process, ensure proper preparation to achieve the best results and maintain safety.

1. Přečtěte si bezpečnostní informace: Opatrně znovuview the Safety Information section and the product's Safety Data Sheet (SDS).
2. Připravte pracovní plochu: Ensure the work area is well-ventilated. If working indoors, open windows and doors, or use exhaust fans. If working outdoors, choose an area away from ignition sources.
3. Gather PPE: Put on appropriate personal protective equipment, including chemical-resistant gloves, eye protection, and if necessary, a respirator.
4. Protect Surrounding Areas: Cover adjacent areas not intended for treatment with drop cloths or plastic sheeting to prevent accidental contact or overspray.
5. Test Surface Compatibility: Apply a small amount of the adhesive remover to an inconspicuous area of the surface. Observe for any adverse reactions such as discoloration, etching, or softening of the material. Proceed only if no damage occurs.
6. Připravte si nástroje: Have clean rags, plastic scrapers, or other non-abrasive tools ready for wiping and scraping the softened adhesive.

Návod k obsluze

Follow these steps for effective removal of reactive adhesives using 3M Specialty Adhesive Remover 38987.

1. Protřepejte plechovku: Shake the aerosol can thoroughly for at least one minute before use to ensure proper mixing of contents.
2. Apply Remover: Hold the can approximately 6-12 inches (15-30 cm) from the surface. Spray a liberal, even coat of the adhesive remover directly onto the adhesive residue. Ensure the adhesive is fully saturated.
3. Allow to Penetrate: Allow the product to dwell on the adhesive for several minutes (typically 5-15 minutes). The exact time may vary depending on the type and thickness of the adhesive. The remover will begin to soften and loosen the adhesive. Do not allow the product to dry on the surface.
4. Scrape/Wipe: Using a plastic scraper or a clean, non-abrasive cloth, gently scrape or wipe away the softened adhesive. For stubborn residues, reapply the remover and allow more dwell time.
5. V případě potřeby opakujte: For heavy or aged adhesive, multiple applications and scraping/wiping cycles may be required.
6. Čistý povrch: After all adhesive residue is removed, wipe the surface clean with a fresh, clean cloth. For best results, follow with a mild soap and water wash, then rinse and dry the surface.
7. Likvidace odpadu: Dispose of all used rags and adhesive residue according to local regulations for hazardous waste.

Údržba

Proper storage ensures the longevity and effectiveness of your 3M Specialty Adhesive Remover 38987.

• Podmínky skladování: Store the product in its original container, tightly closed, in a cool, dry, and well-ventilated area.
• Teplota: Avoid extreme temperatures. Do not store above 120°F (49°C) or below 32°F (0°C).
• Away from Ignition Sources: Keep away from all sources of ignition, including direct sunlight, heat, sparks, and open flames.
• Bezpečnost dětí: Skladujte mimo dosah dětí a domácích zvířat.

Odstraňování problémů

If you encounter issues while using the 3M Specialty Adhesive Remover 38987, consider the following common solutions:

Specifikace

Záruka

The 3M Specialty Adhesive Remover 38987 is covered by a warranty as labeled on the product packaging. For specific details regarding warranty terms and conditions, please refer to the information provided directly on the product container or contact 3M customer service.

Podpora

For additional product information, technical assistance, or safety data sheets, please contact 3M directly or visit their official webmísto.

• Výrobce: 3M
• Webmísto: www.3M.com
• Značková prodejna: 3M Automotive Store on Amazon

For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.