Peiying NB-3000

Peiying NB-3000 Návod k obsluze aktivního subwooferu do auta

Model: NB-3000

1. Úvod

Thank you for choosing the Peiying NB-3000 Active Car Subwoofer. This compact and powerful audio solution is designed to enhance your in-car listening experience by delivering deep, rich bass. Its ultra-flat design allows for versatile placement in vehicles with limited space. Please read this manual thoroughly before installation and operation to ensure proper use and maximize performance.

2. Bezpečnostní informace

VAROVÁNÍ: Improper installation or use can lead to serious injury or damage to the product and vehicle.

  • Před zahájením jakýchkoli elektrických prací vždy odpojte záporný pól baterie vozidla.
  • Ensure all wiring is properly routed and secured to prevent pinching, cutting, or short-circuiting.
  • Pro připojení napájení a uzemnění použijte kabeláž vhodného průřezu, jak je uvedeno v této příručce.
  • Do not install the subwoofer in locations where it may obstruct the driver's view nebo zasahovat do provozu vozidla.
  • Avoid installing the unit in areas exposed to direct sunlight, excessive heat, moisture, or dust.
  • Pokud si nejste jisti některou částí procesu instalace, poraďte se s profesionálním instalatérem autorádií.
  • Nepokoušejte se jednotku otevírat ani upravovat. Zrušíte tak platnost záruky a může dojít k jejímu poškození.

3. Konec produktuview a funkce

The Peiying NB-3000 is an active (amplified) car subwoofer designed for powerful bass reproduction.

Klíčové vlastnosti:

  • 20 cm (8-inch) active subwoofer with 1000 W maximum power output.
  • Flat metal enclosure for low vibration and compact installation.
  • Integrated MOSFET power ampživější.
  • High-level and low-level (RCA) inputs for versatile connection options.
  • Wired remote control for convenient bass level adjustment.

Identifikace součásti:

Peiying NB-3000 Active Car Subwoofer
Obrázek 1: Peiying NB-3000 Active Car Subwoofer. This image displays the overall design of the subwoofer, including the speaker grille and the control panel located on one side.
Peiying NB-3000 Subwoofer Control Panel
Obrázek 2: Control Panel and Connections. This close-up view shows the various inputs and controls: PHASE switch, FREQ (frequency) knob, REMOTE port, MIN/MAX GAIN knob, CH1/CH2 RCA inputs, POWER/PROTECT indicators, and the POWER/HIGH LEVEL INPUT terminal.
Peiying NB-3000 Wired Remote Control
Obrázek 3: Wired Remote Control. This image shows the external wired remote control unit, featuring a power indicator light and a rotary knob for adjusting the subwoofer's output level (MIN/MAX).

4. Nastavení a instalace

Proper installation is crucial for optimal performance and safety. If you are not confident in performing the installation yourself, please seek professional assistance.

4.1. Umístění

The compact design of the NB-3000 allows for flexible placement. Common locations include:

  • Under a car seat (ensure adequate clearance and ventilation).
  • V kufru.
  • Behind a rear seat.

Secure the subwoofer firmly to prevent it from moving during vehicle operation. Use mounting brackets or straps if provided or necessary.

4.2. Připojení vodičů

Before making any connections, ensure the vehicle's battery negative terminal is disconnected.

  1. Připojení napájení (BATT+): Connect a suitable gauge power cable (e.g., 8 AWG or 10 AWG, depending on cable length and power requirements) directly from the vehicle's positive battery terminal to the "POWER" terminal on the subwoofer's high-level input connector. Install an in-line fuse (e.g., 20A-30A) within 18 inches (45 cm) of the battery.
  2. Zemní připojení (GND): Connect a short, heavy gauge ground cable (same gauge as power cable) from the "GND" terminal on the subwoofer's high-level input connector to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical contact.
  3. Dálkové zapnutí (REM): Connect a remote turn-on wire from your car stereo's remote output (usually a blue/white wire) to the "REM" terminal on the subwoofer's high-level input connector. This wire tells the subwoofer to turn on and off with your car stereo. If your stereo does not have a remote output, you may need to use an ignition-switched 12V source.
  4. Zvukový vstup:
    • Nízkoúrovňový vstup (RCA): If your car stereo has RCA pre-outs, connect RCA cables from the stereo's subwoofer or rear pre-outs to the "CH1" and "CH2" RCA inputs on the subwoofer.
    • Vstup na vysoké úrovni: If your car stereo does not have RCA pre-outs, connect the speaker wires from your stereo's rear speakers to the "HIGH LEVEL INPUT" terminals on the subwoofer's connector. Ensure correct polarity (+ to + and - to -).
  5. Dálkové ovládání úrovně: Connect the wired remote control cable to the "REMOTE" port on the subwoofer's control panel. Mount the remote control in a convenient location for the driver.

After all connections are made, reconnect the vehicle's negative battery terminal.

5. Návod k obsluze

Once installed, you can adjust the subwoofer's settings for optimal sound.

5.1. Počáteční zapnutí

Turn on your car stereo. The "POWER" indicator light on the subwoofer's control panel should illuminate (green). If the "PROTECT" light (red) illuminates, there may be a wiring issue or fault. Refer to the Troubleshooting section.

5.2. Nastavení ovládacích prvků

  • ZESILENÍ (MIN/MAX): This knob controls the input sensitivity. Start with the GAIN set to minimum (MIN). Play music with a moderate bass level. Slowly increase the GAIN until the bass output blends well with your main speakers without distortion. Avoid setting the GAIN too high, as this can cause distortion and damage.
  • FREQ (Frekvence): This knob adjusts the low-pass filter (LPF) crossover frequency, typically from 50Hz to 160Hz. The LPF ensures that only low frequencies are sent to the subwoofer. Adjust this to blend smoothly with your main speakers. A common starting point is around 80-100Hz.
  • FÁZE (0°/180°): This switch adjusts the phase of the subwoofer's output relative to your main speakers. Listen to music with strong bass and switch between 0° and 180°. Choose the setting that provides the most impactful and cohesive bass response.
  • REMOTE (Level Control): The wired remote control allows you to conveniently adjust the subwoofer's output level from the driver's seat without accessing the main unit.

6. Údržba

The Peiying NB-3000 requires minimal maintenance.

  • Keep the unit clean by wiping it with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
  • Pravidelně kontrolujte všechna kabelová připojení, abyste se ujistili, že jsou bezpečná a bez koroze.
  • Ensure the area around the subwoofer is clear to allow for proper ventilation.

7. Řešení problémů

If you experience problems with your subwoofer, refer to the following troubleshooting guide.

ProblémMožná příčinaŘešení
No power / No sound
  • Spálená pojistka.
  • Uvolněné napájení nebo uzemnění.
  • Remote turn-on wire not connected or not receiving signal.
  • No audio input signal.
  • Zkontrolujte a v případě potřeby vyměňte pojistku (použijte správnou hodnotu).
  • Ověřte, zda jsou všechna napájecí, uzemňovací a vzdálená připojení bezpečná.
  • Check remote wire connection and ensure car stereo is on.
  • Check RCA or high-level input connections. Ensure stereo output is active.
Zkreslený zvuk
  • Zisk je nastaven příliš vysoko.
  • Incorrect FREQ setting.
  • Špatná kvalita zdroje zvuku.
  • Loose speaker wires (high-level input).
  • Reduce GAIN level.
  • Adjust FREQ knob for a smoother blend.
  • Zkuste jiný zdroj zvuku.
  • Check high-level input connections for proper polarity and secure fit.
Subwoofer se občas vypíná
  • Overheating (PROTECT light on).
  • Loose power/ground connections.
  • Nízký objemtage.
  • Ensure adequate ventilation around the unit. Reduce GAIN.
  • Check and secure all power and ground connections.
  • Verify vehicle's electrical system is functioning correctly.
Slabé nebo žádné basy
  • GAIN set too low.
  • Nesprávné nastavení FÁZE.
  • Incorrect FREQ setting.
  • RCA cables faulty or disconnected.
  • Increase GAIN level.
  • Toggle PHASE switch (0°/180°) to find the best setting.
  • Adjust FREQ knob.
  • Check RCA cable connections and try a different cable if suspected faulty.

8. Specifikace

The following are the technical specifications for the Peiying NB-3000 Active Car Subwoofer:

Název modeluNB-3000
Typ reproduktoruAktivní subwoofer
Velikost reproduktoru20 cm (8 palců)
Maximální výstupní výkon1000 wattů
Ampživější typMOSFET
Frekvenční odezvaAdjustable via LPF (50Hz - 160Hz)
Vstupní citlivostAdjustable (GAIN)
Řízení fáze0° / 180° Switchable
VstupyRCA (Low-Level), High-Level Speaker Input
Kontrolní metodaKabelové dálkové ovládání
Zdroj napájení12V DC autobaterie
MateriálKovový kryt
Rozměry (D x Š x V)35 cm x 23.5 cm x 7 cm (13.78 x 9.25 x 2.76 palce)
Hmotnost5 kg (11 lb)

9. Záruka a podpora

The Peiying NB-3000 Active Car Subwoofer comes with a limited warranty. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact your retailer.

For technical support or service inquiries, please contact the authorized Peiying dealer or the point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.