Uživatelská příručka k detektoru záplav Diversitech WS-1 Wet Switch

1. Konec produktuview

The Diversitech WS-1 Wet Switch Flood Detector is an electronic device designed to detect the presence of water and trigger a connected system shutdown or alarm. It utilizes a hydrophilic pad to quickly draw water into its sensor array, providing early detection of leaks or floods. The unit operates on a standard 24VAC control voltage and includes integrated test and reset buttons for user convenience.

Figure 1: The Diversitech WS-1 Wet Switch Flood Detector. This image displays the top of the circular detector, showing the "WET SWITCH FLOOD DETECTOR" label, "Power On" and "Moisture" indicator lights, "Push to Test" and "Push to Reset" buttons, and a clear wiring diagram for 24VAC power (Red, Black) and contact connections (Orange, White, Green).

2. Bezpečnostní informace

• Always disconnect power to the system before installation or maintenance.
• Instalaci by měl provést kvalifikovaný technik v souladu s místními elektrotechnickými předpisy.
• Ensure the detector is installed in a location where it can accurately detect water without being exposed to splashing or condensation that could cause false alarms.
• The device operates on 24VAC. Do not connect to higher voltage zdroje.

3. Pokyny k instalaci

3.1 Umístění

Position the Wet Switch Flood Detector in areas prone to water leaks, such as HVAC drain pans, near water heaters, washing machines, or under sinks. The detector features integral feet that raise it slightly to prevent direct contact with the pan surface, which helps to avoid corrosion and ensures proper water wicking to the sensor.

Figure 2: The WS-1 detector placed within an HVAC drain pan, demonstrating typical installation for water detection. The detector is positioned on the pan floor, ready to sense any accumulating water.

3.2 Zapojení

The WS-1 operates on 24VAC and provides a set of dry contacts for integration into control circuits. Refer to the wiring diagram on the device (also shown in Figure 1) for connections:

• Power Input (24VAC): Connect the 24VAC power supply to the ČERVENÝ a ČERNÝ dráty.
• Control Contacts: The POMERANČOVÝ, BÍLÝa ZELENÝ wires provide the contact closure. These contacts are typically wired in series with the low-voltage control circuit of the equipment (e.g., HVAC unit, pump) to shut it down upon water detection. Consult the equipment's wiring diagram for proper integration.

Ensure all connections are secure and insulated according to electrical standards.

3.3 Počáteční test

After installation and power-up, perform an initial test to verify proper operation:

1. Observe the "Power On" indicator light. It should be green, indicating the unit is receiving power.
2. Press and hold the "Push to Test" button. The "Moisture" indicator light should turn red, and the connected equipment should shut down or trigger an alarm, simulating a water detection event.
3. Release the "Push to Test" button. The "Moisture" light should turn off.
4. Press the "Push to Reset" button to restore the system to normal operation if it was shut down.

4. Provoz

4.1 Normální provoz

When the Wet Switch Flood Detector is powered and no water is detected, the "Power On" indicator light will be green. The control contacts remain in their normal state, allowing connected equipment to operate.

Figure 3: The WS-1 detector showing a green "Power On" indicator light, signifying normal operation with no water detected.

4.2 Detekce vody

Upon contact with water, the hydrophilic pad quickly absorbs moisture, activating the sensor array. The "Moisture" indicator light will turn red, and the internal contacts will change state, typically shutting down the connected equipment to prevent further water damage.

Figure 4: The WS-1 detector displaying a red "Moisture" indicator light, indicating that water has been detected and the unit has tripped.

5. Údržba

The Wet Switch Flood Detector requires minimal maintenance. After a water detection event, follow these steps:

1. Address the source of the water leak and remove any standing water from the sensor area.
2. Ensure the hydrophilic pad on the detector is completely dry. You may gently wipe it with a dry cloth.
3. Once dry, press the "Push to Reset" button to clear the fault and restore the connected equipment to operation. The "Moisture" indicator light should turn off.

It is recommended to periodically test the unit (e.g., monthly or quarterly) using the "Push to Test" button to ensure it is functioning correctly.

6. Řešení problémů

7. Technické specifikace

• Model: WS-1
• Značka: Diversitech
• svtage: 24 voltů AC
• Způsob ovládání: Touch (for test/reset buttons)
• Technologie senzoru: Contact Sensor (hydrophilic pad)
• Rozměry produktu: 7.5" L x 4.1" W x 1.5" H (approximate, based on product dimensions)
• Hmotnost položky: 2.08 unce
• UPC: 095247149995, 686109990048, 094717313904, 094714370160
• Výrobce: DiversiTech

8. Záruka a podpora

Specific warranty information for the Diversitech WS-1 Wet Switch Flood Detector is not provided within this manual. For details regarding warranty coverage, terms, and conditions, please refer to the documentation included with your purchase or contact Diversitech directly.

For technical support or further assistance, please visit the official Diversitech webstránky nebo kontaktujte jejich oddělení zákaznických služeb. Kontaktní informace obvykle naleznete na obalu výrobce nebo webmísto.