Timex Men's Ironman Triathlon Endure 30 Shock 42mm Watch Instruction Manual

Zavedení

Welcome to the instruction manual for your Timex Men's Ironman Triathlon Endure 30 Shock 42mm Watch. This durable and lightweight timepiece is designed for active lifestyles, offering improved functionality and shock-resistant durability. It features a 100-hour chronograph, 30-lap memory, 24-hour countdown timer, multiple alarms, and is water-resistant up to 200m.

Obrázek 1: Přední strana view of the Timex Men's Ironman Triathlon Endure 30 Shock 42mm Watch.

Figure 2: Timex brand philosophy emphasizing timeless watchmaking.

Nastavení

Nastavení času a data

To set the time and date on your watch, follow these steps. The watch allows for two independent time zones (Time 1 and Time 2).

1. From the timekeeping mode, press and hold the NASTAVIT/VYVOLAT button (top-left) for a few seconds until the display shows "HOLD TO SET" and then "SET TIME".
2. The current time zone (e.g., "TIME 1" or "TIME 2") will blink. Use the START/ROZDĚLENÍ button (bottom-middle) to increment the value or STOP/RESET button (bottom-right) to decrement.
3. Stiskněte tlačítko MODE button (bottom-left) to move to the hour setting. Adjust the hour using the START/ROZDĚLENÍ or STOP/RESET buttons. Pay attention to the AM/PM indicator if using 12-hour format.
4. Stiskněte MODE again to set the minutes, then seconds.
5. Pokračujte v stisknutí MODE to cycle through and set the month, day, and year. The year setting is crucial for correct day-of-the-week display.
6. Jakmile jsou všechna nastavení provedena, stiskněte tlačítko NASTAVIT/VYVOLAT button to exit the setup mode.

Změna formátu data

You can switch between Month-Day (MM-DD) and Day-Month (DD-MM) display formats.

1. Stiskněte a podržte NASTAVIT/VYVOLAT button until you enter the setup mode.
2. Stiskněte tlačítko MODE button repeatedly (about 7 times) until you see "DATE" and the current date format (e.g., "MM.DD" or "DD.MM") blinking.
3. Použijte START/ROZDĚLENÍ or STOP/RESET buttons to toggle between the available date formats.
4. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení změn a ukončení.

Provozní

Button Tones

The watch provides audible feedback (beeps) when buttons are pressed. You can enable or disable this feature.

1. From the timekeeping mode, press and hold the NASTAVIT/VYVOLAT button until you enter the setup mode.
2. Stiskněte tlačítko MODE button repeatedly (about 10 times) until you see "BEEP" and either "ON" or "OFF" blinking.
3. Použijte START/ROZDĚLENÍ or STOP/RESET buttons to toggle the button tone feature on or off.
4. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení změn a ukončení.

Time Format (12hr vs. 24hr)

You can choose to display the time in either 12-hour (with AM/PM indicator) or 24-hour format for each time zone.

1. Stiskněte a podržte NASTAVIT/VYVOLAT button until you enter the setup mode.
2. The current time zone (e.g., "TIME 1" or "TIME 2") will blink. If you want to change the format for the other time zone, use the START/ROZDĚLENÍ or STOP/RESET buttons to select it.
3. Stiskněte tlačítko MODE button repeatedly (about 7 times) until you see "TIME" and either "12HR" or "24HR" blinking.
4. Použijte START/ROZDĚLENÍ or STOP/RESET buttons to toggle between 12-hour and 24-hour format.
5. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení změn a ukončení.

Setting T2 (2nd Time Zone)

Your watch supports a second time zone (T2), which is useful for travelers. You can set T2 independently and quickly switch between T1 and T2 displays.

1. From the timekeeping mode, press and hold the NASTAVIT/VYVOLAT button until you enter the setup mode.
2. Použijte START/ROZDĚLENÍ or STOP/RESET buttons to select "TIME 2" if it's not already blinking.
3. Stiskněte tlačítko MODE button to move to the hour setting for T2. Adjust the hour, minutes, and seconds as desired.
4. Pokračujte v stisknutí MODE to cycle through and set the month, day, and year for T2.
5. Stiskněte tlačítko NASTAVIT/VYVOLAT button to exit the setup mode.
6. To quickly toggle between T1 and T2 displays, press and hold the START/ROZDĚLENÍ button from the main timekeeping mode.

Stopwatch / Chronograph

The chronograph function allows you to measure elapsed time, including lap and split times.

1. From the timekeeping mode, press the MODE button once to enter the Chronograph mode. The display will show "CHRONO" and "00:00:00".
2. Stiskněte tlačítko START/ROZDĚLENÍ tlačítko pro spuštění měření času.
3. To record a lap time while the stopwatch is running, press the START/ROZDĚLENÍ button. The top display will show the lap time, and the bottom display will show the total elapsed time.
4. Chcete-li stopky pozastavit, stiskněte tlačítko STOP/RESET button (bottom-right). Press START/ROZDĚLENÍ obnovit.
5. Chcete-li stopky vynulovat, stiskněte tlačítko STOP/RESET button while it is paused, then press and hold it again until it resets.
6. The watch stores up to 30 lap times. To recall stored lap times, press the NASTAVIT/VYVOLAT button from the Chronograph mode while the stopwatch is stopped.

Odpočítávací časovač

The countdown timer can be set for up to 24 hours and can be configured to stop or repeat when it reaches zero.

1. From the timekeeping mode, press the MODE button twice to enter the Timer mode. The display will show "TIMER".
2. To set the timer duration, press and hold the NASTAVIT/VYVOLAT button. Adjust the hours, minutes, and seconds using the START/ROZDĚLENÍ or STOP/RESET tlačítka.
3. Stiskněte MODE pro pohyb mezi hodinami, minutami a sekundami.
4. Po nastavení času stiskněte MODE again to select the timer's action when it reaches zero: "AT END" (stops) or "REPEAT" (repeats the countdown).
5. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení vašich nastavení.
6. Chcete-li spustit odpočítávání, stiskněte tlačítko START/ROZDĚLENÍ button. To pause, press STOP/RESETChcete-li pokračovat, stiskněte START/ROZDĚLENÍ.
7. Chcete-li časovač resetovat, stiskněte STOP/RESET while it is paused, then press and hold it again.

Poplach

The watch features three daily, weekday, or weekend alarms.

1. From the timekeeping mode, press the MODE button three times to enter the Alarm mode. The display will show "ALARM".
2. Chcete-li nastavit čas budíku, stiskněte a podržte tlačítko NASTAVIT/VYVOLAT button. Adjust the hour and minutes using the START/ROZDĚLENÍ or STOP/RESET buttons. Pay attention to AM/PM.
3. Stiskněte MODE to move between hour and minutes.
4. Po nastavení času stiskněte MODE again to select the alarm frequency: "DAILY", "WEEKDAY", or "WEEKEND".
5. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení vašich nastavení.
6. Chcete-li aktivovat nebo deaktivovat budík, stiskněte tlačítko START/ROZDĚLENÍ button from the Alarm mode. An alarm icon will appear/disappear on the main display.

HourlSignál y

Hourly signal (chime) provides an audible beep every hour on the hour.

1. From the timekeeping mode, press and hold the NASTAVIT/VYVOLAT button until you enter the setup mode.
2. Stiskněte tlačítko MODE button repeatedly (about 9 times) until you see "CHIME" and either "ON" or "OFF" blinking.
3. Použijte START/ROZDĚLENÍ or STOP/RESET buttons to toggle the hourly chime on or off.
4. Stiskněte tlačítko NASTAVIT/VYVOLAT tlačítko pro uložení změn a ukončení.

Backlight / Indiglo Night Mode

The Indiglo backlight illuminates the watch display for easy viewing in low-light conditions. Night Mode keeps the backlight active for a set period with any button press.

1. To activate the Indiglo backlight, press the INDIGLO button (top-right). The light will stay on for approximately 3 seconds.
2. To activate Night Mode, press and hold the INDIGLO button for 4 seconds. A moon icon will appear on the display.
3. In Night Mode, any button press will activate the backlight for 3 seconds.
4. Night Mode will automatically turn off after 8 hours, or you can deactivate it manually by pressing and holding the INDIGLO znovu na 4 sekund.

Údržba

Voděodolnost

Your Timex Ironman watch is water-resistant to 200 meters (660 feet). This makes it suitable for professional marine activity and serious surface water sports. It is ne suitable for scuba diving.

Baterie

The watch uses 1 Lithium Metal battery, which is included. Battery life varies depending on usage of features like the backlight and alarms.

Čištění a péče

To maintain your watch, regularly wipe the resin case and nylon strap with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners. Rinse with fresh water after exposure to salt water or chlorine.

Figure 3: Close-up of the watch on a wrist, highlighting the durable strap.

Odstraňování problémů

Problémy se zobrazením

• Blank or Faint Display: Baterie může být slabá nebo vybitá. Vyměňte baterii.
• Nesprávný čas/datum: Viz Nastavení času a data section to re-adjust. Ensure the correct year is set for accurate day-of-the-week display.

Porucha tlačítka

• Tlačítka nereagují: Ensure the watch is not in a locked mode (if applicable, though this model does not have a specific lock feature). If unresponsive, a battery replacement might be needed, or a soft reset (refer to general digital watch reset procedures if not covered in this manual).
• No Button Tones: Viz Button Tones section to ensure they are enabled.

Specifikace

• Model: T5K198SU
• Materiál: Resin (case), Nylon (strap)
• Rozměry produktu: 6 x 6 x 6 palce; 1.76 unce
• Baterie: 1 lithiová kovová baterie (součástí balení)
• Voděodolnost: 200m (660 ft)
• Výrobce: Timex
• Datum první dostupnosti: 1. října 2001

Záruka a podpora

For detailed warranty information and further support, please refer to the official user manual PDF or visit the Timex Store.

• Oficiální uživatelská příručka (PDF): https://manuals.plus/m/037087c5d633048905b84795555d2880139e077b8ef3431925f6841ad2dfc006
• Visit the Timex Store: https://www.amazon.com/stores/Timex/page/4619EC3B-E9F4-40E0-B3AF-822D9645AEEC