Zavedení
This manual provides essential instructions for the safe operation, maintenance, and storage of your Performance Tool W1611 2.25 Ton (4,500 lbs) Capacity Trolley Jack. Before using the jack, it is crucial to read and understand all instructions and safety warnings to prevent injury or property damage. Keep this manual for future reference.
Image: The Performance Tool W1611 2.25 Ton Trolley Jack, a yellow hydraulic jack with a long handle.
Důležité bezpečnostní informace
WARNING: Failure to heed these warnings may result in personal injury or property damage.
- Přečtěte si všechny pokyny: Understand the operation and limitations of the jack, as well as the hazards involved.
- Použití na tvrdém, rovném povrchu: Always use the jack on a hard, level surface capable of supporting the load. Avoid soft ground or uneven surfaces.
- Nepřekračujte jmenovitou kapacitu: The W1611 jack has a maximum capacity of 2.25 tons (4,500 lbs). Do not attempt to lift loads heavier than this rating.
- Použijte stojany Jack: This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a jack.
- Vycentrujte zátěž: Ujistěte se, že je zátěž vystředěna na sedle zvedáku. Zátěž mimo střed může způsobit nestabilitu.
- Udržujte jasno: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
- Před každým použitím zkontrolujte: Check the jack for any damage, leaks, or loose parts before each use. Do not use if damaged.
- Pomalu dolů: Always lower the load slowly and in a controlled manner.
- Návrh 65 Varování: Tento produkt může obsahovat chemikálie, o kterých je ve státě Kalifornie známo, že způsobují rakovinu a vrozené vady nebo jiná poškození reprodukce. Po manipulaci si umyjte ruce.
Obsah balení
Po vybalení ověřte, zda jsou přítomny všechny komponenty:
- 1 Performance Tool W1611 2.25 Ton Trolley Jack
- 1 Ovládací rukojeť
- 1 Blow-molded plastic storage case
Specifikace
| Funkce | Specifikace |
|---|---|
| Model | W1611 |
| Kapacita zatížení | 2.25 tun (33 000 liber) |
| Minimální výška zdvihu | 5-1/4 palce |
| Maximální výška zdvihu | 15 palců |
| Rozměry produktu (D x Š x V) | 23.2 x 10.3 x 6.8 palce |
| Hmotnost položky | Approximately 27 lbs (including case) |
| Sedlo | Steel lifting saddle with 360-degree swivel |
| Kola | Heavy-duty steel front wheels, ball-bearing swivel rear wheels |
Obrázek: Detail view highlighting the steel lifting saddle and the heavy-duty wheels of the trolley jack.
Nastavení a počáteční příprava
1. Vybalování
Carefully remove the trolley jack and its components from the packaging. Inspect for any shipping damage. If any damage is found, do not use the jack and contact customer support.
2. Montáž rukojeti
Insert the operating handle into the handle socket on the jack. Ensure it is securely seated. Some models may require tightening a set screw.
3. Bleeding the Hydraulic System
Before first use, or if the jack has been stored for an extended period, it is recommended to bleed any air from the hydraulic system to ensure proper operation. This procedure helps distribute fluid evenly through internal components.
- Locate the release valve (typically a screw or knob near the handle socket).
- Turn the release valve counter-clockwise to open it fully.
- Pump the handle vigorously six (6) to ten (10) times. This action will cycle the hydraulic fluid and expel any trapped air.
- Turn the release valve clockwise to close it firmly. The jack is now ready for use.
Návod k obsluze
1. Zvedání vozidla
- Připravte vozidlo: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground to prevent movement.
- Umístění zvedáku: Locate the manufacturer-recommended lifting points on your vehicle's frame or chassis. Position the jack so the saddle is directly under the lifting point. Ensure the jack is stable and the load is centered on the saddle.
- Zvedněte vozidlo: Close the release valve by turning it clockwise until it is firm. Pump the operating handle up and down to raise the vehicle to the desired height.
- Zajištění pomocí zvedáků: Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.
2. Spouštění vozidla
- Vyčistěte oblast: Ensure all tools, personnel, and obstructions are clear from under and around the vehicle.
- Mírně zvedněte: If the vehicle is on jack stands, pump the jack handle a few times to lift the vehicle slightly off the jack stands.
- Demontáž podpěr: Opatrně vyjměte zvedáky zpod vozidla.
- Spusťte vozidlo dolů: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Once fully lowered, remove the jack.
Image: The Performance Tool W1611 trolley jack positioned for lifting, demonstrating its extended handle and low profile.
Údržba
Regular maintenance ensures the longevity and safe operation of your trolley jack.
- Čištění: Keep the jack clean and free of dirt, grease, and debris. Wipe down the exterior with a clean cloth after each use.
- Mazání: Periodically lubricate the pivot points, wheels, and especially the wheel castor bearings with light machine oil to ensure smooth operation and prevent rust.
- Hydraulická kapalina: Check the hydraulic fluid level periodically. If the fluid level is low, consult a qualified service technician for proper refilling with hydraulic jack oil. Do not use brake fluid or other non-specified fluids.
- Inspekce: Regularly inspect the jack for any signs of wear, damage, or leaks. Pay close attention to welds, the hydraulic cylinder, and the handle. If any issues are found, discontinue use and have it repaired by a qualified professional.
Odstraňování problémů
Běžné problémy a jejich možná řešení naleznete v tabulce níže.
| Problém | Možná příčina | Řešení |
|---|---|---|
| Jack will not lift or lifts slowly | Vzduch v hydraulickém systému Nízká hladina hydraulické kapaliny Uvolňovací ventil není zcela uzavřen | Bleed the hydraulic system (refer to Setup section) Consult a qualified technician to check/refill fluid Ensure release valve is firmly closed clockwise |
| Jack lowers under load | Uvolňovací ventil není zcela uzavřen Internal hydraulic leak Přetížení | Ensure release valve is firmly closed Discontinue use and consult a qualified technician Ensure load does not exceed 2.25 tons (4,500 lbs) |
| Jack is difficult to pump | Vzduch v hydraulickém systému Nedostatek mazání na pohyblivých částech Poškozený mechanismus čerpadla | Odvzdušněte hydraulický systém Lubricate pivot points and wheels Poraďte se s kvalifikovaným technikem |
Skladování
Proper storage helps maintain the jack's condition and readiness for use.
- Před uskladněním vyčistěte: Ensure the jack is clean and dry before storing.
- Lower Ram Fully: Always lower the jack's ram completely before storage to relieve pressure on the hydraulic system.
- Použijte úložný kufřík: Store the jack in its provided blow-molded plastic case to protect it from dust, moisture, and damage. This also prevents it from rolling around if stored in a vehicle.
- Skladujte na suchém místě: Store the jack in a dry, protected area, away from corrosive materials and extreme temperatures.
Image: The Performance Tool W1611 trolley jack alongside its durable black plastic storage case, emphasizing portability and protection.
Záruka a podpora
For warranty information or technical support regarding your Performance Tool W1611 2.25 Ton Trolley Jack, please refer to the documentation included with your purchase or visit the official Performance Tool webKontaktní údaje zákaznického servisu jsou obvykle k dispozici na webových stránkách výrobce. webmísto nebo obal produktu.
Můžete navštívit Obchod s výkonnostním nářadím na Amazonu pro více informací o produktu a zdroje podpory.