Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack User Manual

Zavedení

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack. Designed for heavy-duty lifting tasks, this floor jack is constructed from durable steel and features swivel rear casters for easy positioning. It has a maximum lifting capacity of 4,000 pounds and can reach a maximum height of 15 inches.

Figure 1: Performance Tool W1614 2 Ton Floor Jack.

Bezpečnostní informace

UPOZORNĚNÍ: Tento výrobek vás může vystavit chemikáliím včetně olova, které je ve státě Kalifornie známo, že způsobuje rakovinu a vrozené vady nebo jiné poškození reprodukce. Pro více informací přejděte na www.P65Warnings.ca.gov.

Always read and understand all instructions and warnings before using this floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Použití na tvrdém, rovném povrchu: Always operate the jack on a hard, level surface capable of supporting the load.
• Použijte stojany Jack: This floor jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by a floor jack.
• Nepřekračujte jmenovitou kapacitu: Never exceed the 4,000 lbs. (2 Ton) rated capacity of this jack.
• Center Load on Saddle: Ensure the load is centered on the jack saddle to prevent slipping.
• Chock Wheels: Always chock the wheels that are not being lifted.
• Udržujte jasno: Udržujte ruce, nohy a další části těla v dostatečné vzdálenosti od pohyblivých částí a míst, kde se skřípnete.
• Před použitím zkontrolujte: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• Ochrana proti přetížení: This jack is equipped with an overload protection bypass valve for safety. Do not attempt to bypass or modify this feature.

Nastavení a počáteční příprava

Before first use, or if the jack has been stored for an extended period, it is important to bleed any air from the hydraulic system to ensure proper operation. Air in the system can cause the jack to lift unevenly or not lift at all.

Bleeding the Hydraulic System:

1. Locate the release valve. This is typically a screw or knob that controls the lowering function.
2. Vložte rukojeť do objímky rukojeti.
3. Otočte rukojetí proti směru hodinových ručiček, abyste zcela otevřeli vypouštěcí ventil.
4. Pump the handle fully up and down approximately 10-15 times to force any trapped air out of the system.
5. Otočením rukojeti ve směru hodinových ručiček uzavřete vypouštěcí ventil.
6. Test the jack by pumping the handle to raise the saddle. It should raise smoothly and evenly. If not, repeat the bleeding process.

Obrázek 2: Úhlové view of the floor jack, showing the handle socket and general structure.

Návod k obsluze

Zvedání vozidla:

1. Park the vehicle on a hard, level surface. Engage the parking brake and chock the wheels that will remain on the ground.
2. Locate the vehicle's manufacturer-recommended lifting points. Refer to your vehicle's owner's manual.
3. Position the floor jack so that the saddle is directly under the lifting point. Ensure the load is centered on the saddle.
4. Close the release valve by turning the handle clockwise until it is firmly closed. Do not overtighten.
5. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to place jack stands.
6. Immediately place appropriately rated jack stands under the vehicle's designated support points.
7. Slowly open the release valve by turning the handle counter-clockwise to lower the vehicle onto the jack stands. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Spouštění vozidla:

1. Ensure the area around the vehicle is clear of obstructions and personnel.
2. Position the floor jack saddle directly under the vehicle's lifting point, adjacent to the jack stands.
3. Pump the jack handle a few times to slightly raise the vehicle off the jack stands.
4. Opatrně vyjměte zvedáky zpod vozidla.
5. Slowly turn the jack handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Once the vehicle is fully lowered, remove the floor jack.

Figure 3: Diagram showing key dimensions and lift range of the floor jack.

Údržba

• Mazání: Periodically lubricate all moving parts with light machine oil.
• Hydraulická kapalina: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other types of oil.
• Čištění: Udržujte zvedák čistý a bez nečistot, mastnoty a úlomků.
• Skladování: Store the jack in a dry, clean place with the ram fully retracted to prevent rust and extend seal life.
• Inspekce: Regularly inspect for any signs of wear, damage, or leaks. If any issues are found, do not use the jack and have it serviced by qualified personnel.

Odstraňování problémů

Specifikace

Záruka a podpora

For specific warranty information, please refer to the documentation included with your purchase or contact Performance Tool customer service. Keep your purchase receipt for warranty claims.

Oficiální uživatelská příručka (PDF) je k dispozici ke stažení: Stáhnout uživatelskou příručku (PDF)

For technical support or inquiries, please visit the official Performance Tool webnebo kontaktujte jejich oddělení zákaznických služeb.