Mibro 155120 Spiral Flute Screw Extractor Set User Manual

Zavedení

The Mibro 155120 Spiral Flute Screw Extractor Set is designed for removing broken or stripped screws, bolts, and studs. This 5-piece set provides a reliable solution for fasteners that cannot be removed with standard tools. Each extractor features a left-hand spiral flute design to grip and extract the damaged fastener when turned counter-clockwise.

Image: The complete Mibro 155120 screw extractor set, showing all five extractors neatly organized within their transparent blue storage case.

Bezpečnostní informace

• Vždy používejte vhodné osobní ochranné prostředky, včetně ochranné brýle, to protect against flying debris.
• Ujistěte se, že je obrobek bezpečně třamped or held to prevent movement during extraction.
• Use the correct size extractor for the damaged fastener to prevent further damage or injury.
• Do not apply excessive force, which can break the extractor or damage the surrounding material.
• Keep hands and fingers clear of rotating tools.
• Store extractors in their case when not in use to prevent damage and loss.

Komponenty

The Mibro 155120 set includes five spiral flute screw extractors of varying sizes, designed to handle a range of fastener diameters.

• Extractor #1
• Extractor #2
• Extractor #3
• Extractor #4
• Extractor #5

Each extractor is clearly marked for easy identification.

Nastavení

1. Prepare the Fastener: Ensure the broken or stripped fastener is accessible and clean. If the fastener is broken below the surface, a pilot hole must be drilled.
2. Drill a Pilot Hole (if necessary): Using a drill bit slightly smaller than the extractor, drill a straight hole into the center of the damaged fastener. The depth of the hole should be sufficient for the extractor to get a firm grip. For best results, use a drill guide to keep the hole centered and straight.
3. Select Extractor Size: Choose the extractor that fits snugly into the pilot hole. The extractor should be large enough to provide sufficient torque without breaking, but not so large that it cannot enter the hole.

Návod k obsluze

1. Insert Extractor: Insert the selected spiral flute extractor into the pre-drilled pilot hole. Tap it gently with a hammer if needed to ensure it seats firmly.
2. Attach Turning Tool: Use an appropriate turning tool, such as a tap wrench or adjustable wrench, to grip the square end of the extractor.
3. Extract the Fastener: Slowly turn the extractor proti směru hodinových ručiček. As you turn, the left-hand spiral flutes will bite into the metal of the damaged fastener. Apply steady, even pressure while turning.
4. Continue Turning: Continue turning counter-clockwise until the damaged fastener loosens and can be removed. If resistance is high, apply penetrating oil and allow it to soak before attempting again.

Obrázek: Podrobný view of a single Mibro spiral flute screw extractor, highlighting its tapered, left-hand spiral design for effective grip.

Obrázek: Vedlejší profesionálfile of a Mibro screw extractor, illustrating the square drive end designed for use with a wrench or tap handle.

Údržba

• After each use, clean the extractors to remove any metal shavings or debris.
• Apply a light coat of rust-preventative oil if storing in a humid environment.
• Store the extractors in their original case to protect them from damage and keep them organized.
• Inspect extractors for wear or damage before each use. Do not use damaged extractors.

Odstraňování problémů

• Extractor slips:
  • Ujistěte se, že je pilotní otvor vyvrtán na správnou velikost a hloubku.
  • Verify the extractor is fully seated and gripping the fastener.
  • Try a slightly larger extractor if the hole allows, or re-drill the pilot hole if possible.
• Fastener does not turn:
  • Apply penetrating oil to the fastener and allow it to soak for several minutes.
  • Gently tap the extractor with a hammer to help break the bond of the fastener.
  • Ensure you are turning the extractor proti směru hodinových ručiček.
• Extractor breaks:
  • To obvykle naznačuje nadměrnou sílu nebo nesprávně dimenzovaný pilotní otvor.
  • Removing a broken extractor from a fastener can be challenging and may require specialized tools or professional assistance.

Specifikace

Záruka a podpora

This Mibro product comes with a Spokojenost zaručena warranty. For specific details regarding warranty claims or product support, please refer to the manufacturer's official documentation or contact Mibro customer service.

For returns or replacements, please consult the retailer's return policy. For purchases made through Amazon, a 30-day refund/replacement policy is typically available.